How can i locate the sensore PO111

https://www.google.com/search?q=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&rlz=1C1CHBF_enUS982US982&oq=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&aqs=chro -------------------https://www.google.com/search?q=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&rlz=1C1CHBF_enUS982US982&oq=Crankshaft+position+sensor+location+93+ranger+4.0+4x4&aqs=chrome..69i57j33i299l3.7225j0j7&sourceid=chrome&ie=UTF-8#kpvalbx=_VCj-YqCEB6GpptQPza2F-AU28

The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The camshaft position sensor is either located near the top of the engine, passenger-s side, or on the right side of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the camshaft pulley.
This sensor is located at the front of the engine near the camshaft gear this is what I got 6 different locations manual covers 99-05

Engine miss #2 cylinder

P0111 HYUNDAI - Intake Air Temperature Sensor 1 Circuit Range/Performance Problem.
It is very likely the sensor got disconnected during some service work like replacing the engines air filter.
Other causes- Dirty air filter
- Intake air temperature (IAT) sensor harness is open or shorted
- Intake air temperature (IAT) sensor electrical circuit poor connection
- Faulty intake air temperature sensor

Read more: http://engine-codes.com/p0111_hyundai.html#ixzz290YBI1ZJ

• Up-stream sensor (located before catalytic converter)
• Left up-stream sensor (located before catalytic converter)
• Left down-stream sensor (located after catalytic converter)
• Right up-stream sensor (located before catalytic converter)
• Right down-stream sensor (located after catalytic converter)

4 sensors total.

Single or double overhead cam type engine? In any case, these are the locations listed below.

• Up-stream sensor (located before catalytic converter)
• Left up-stream sensor (located before catalytic converter)
• Left down-stream sensor (located after catalytic converter)
• Right up-stream sensor (located before catalytic converter)
• Right down-stream sensor (located after catalytic converter)

For Hyundai Car 1999-05 - Intake Air Temperature (IAT) Sensor Location (check several options):

1.- The IAT sensor is located against the firewall to the left side of the engine. It is combined with the Manifold Absolute Pressure (MAP) sensor.

2.- This sensor is located in the air intake plenum assembly. On some vehicles this sensor is combined with the MAP/MAF sensor.

3.- The IAT sensor is located in the air plenum assembly. On some vehicles it is combined with the MAF sensor.

4.- This sensor is located in the air intake plenum assembly. On some vehicles this sensor is combined with the MAP/MAF sensor.

5.- This sensor is located in the air intake plenum assembly. It is combined with the Manifold Absolute Pressure (AFS) sensor.

6.- This sensor is located in the air intake plenum assembly. It is combined with the Manifold Absolute Pressure (AFS) sensor.


In the next graphic, check the position 2...



FIG : Underhood sensor locations-Elantra 2004-2005 2.0L engine


Hope this help (remember comment and rated this) TY for using Fixya.

B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter

You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks

Oxygen sensors are always numbered like this:

Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Most GM engines have #1 cylinder located on the left bank, (or Driver's Side) of the engine,

So, the answer to your question would be that you are looking for the sensor located before the catalytic converter on the right (or Passenger Side) of the truck.

Intake Air Temperature Sensor Circuit Range/Performance
Possible Causes:


IAT sensor signal circuit has high resistance IAT sensor has drifted out of calibration IAT sensor is damaged or has failed PCM has failed