Toyota mark ll 1G-FE timing diagram - 2001 Dodge Stratus

No maker car, or model car told or year. (or truck)
zero
just an engine floating in space
sorry the books are sold based on the VEHICLE and VIN code for engine.

Do you build engines off internet rumors./ <<<<<brave no?
off
Used on: Lexus IS, Toyota Altezza, Toyota Chaser, Toyota Cresta, Toyota Crown, Toyota Mark II, Toyota Soarer, Toyota Supra, Toyota Verossa
History, I bet they are NOT THE SAME.

1G-FE (1988 - 2005) - version of 1G-GEU with a different narrow 24 valve cylinder head, designed to replace 1G-EU. Power 135 hp at 5600 rpm, torque 176 Nm at 4400 rpm. Installed on: Toyota Mark 2 X90, Cresta X80/X90, Crown S140, Soarer Z20. Since 1996, there has been a restyling and power has grown to 140 hp at 5750 rpm, a torque of 185 Nm at 4400 rpm. Cars with this engine: Toyota Chaser X100, Mark 2 X100, Cresta X100, Crown S150.

if yes bingo this is a car and want facts
read them here, I must pay to read , real books, or like this.

https://eautorepair.net/Marketing/Default.asp

you can get guide from many sites.. i know few
error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassembly, complete re furbish, repair, installation every single thing is covered
within seconds u can get the access and it's totally illustrative complete

Use a scan tool to retrieve the trouble codes from the computer.The code will help lead you to the trouble.

Toyota

i know a website that has very good manuals online, without expiry i.e. for lifetime. www.reliable-store.com
they can help you with this

Download Link:
2004 toyota corolla factory service repair manual PDF DOWNLOAD

Timing marks 2000 Toyota corolla (4E-FE/ 4A-FE/ 5A-FE)


Align the crankshaft pulley mark with the 0 mark of timing case.

The camshaft sprocket is at TDC when the hole in the sprocket lines up with the notch in the bearing cap

Timing marks 2000 Toyota Corolla (1ZZ-FE/ 3ZZ-FE/ 4ZZ-FE/ 2ZZ-GE)

Set the Crankshaft key in 12 'o Align yellow timing chain mark
Clock position (The key aligns on the crankshaft sprocket
with the mark on the oil pump (see arrow)
body (see arrow mark)

Align the marks on the sprockets Place the crankshaft angle plate
with the yellow links of the timing with the marks B or F, facing
chain. towards you.

To your direct question - I am sorry, I do not have anything on that engine.

There may be something useful here

http://www.gizzmoelectronics.com/Toyota%20MARK%202%20JZX110%2000.9~%20ECU%20Pin%20out.html

On the 4A-FE engine do the following:
Align the camshaft knock pin with the knock pin groove on the pulley side with the K mark, the slide on the timing pulley.
Align the camshaft knock pin with the knock pin groove of the pulley, and slide on the pulley.

Align the camshaft knock pin with the groove on the pulley side with the K mark-4A-FE engine
Temporarily install the timing pulley bolt. Hold the hexagonal wrench head portion of the camshaft with a wrench, and then tighten the timing pulley bolt to 43 ft. lbs. (59 Nm).
Install the crankshaft pulley. Align the pulley set key with the groove of the pulley. Slide on the timing pulley, facing the flange side inwards.





Guru..saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

plz I need Toyota 1G FE ECU Pinout Diagram
thanx