P1361 code on 1999 buick park avenue

SOURCE: P1404 error code

The PCM monitors the exhaust gas recirculation (EGR) valve pintle position input to ensure that the valve responds properly to commands from the PCM. When the ignition switch is turned ON, the PCM learns the EGR learned minimum position. The PCM compares the EGR learned minimum position to the EGR position sensor when the EGR valve is commanded closed. If the EGR position sensor indicates that the EGR valve is still open when the PCM is commanding the EGR valve closed, this DTC will set.

Excess deposits on the EGR valve pintle or seat--Remove the EGR valve and check for deposits that may interfere with the EGR valve pintle extending completely or cause the pintle to stick.

Usually this will fix it but in some cases you may have to replace the egr valve.

Donnie Matney

• 426 Answers
• Posted on Jun 19, 2009

SOURCE: Cannot change 3 rear spark plugs on 1999 Buick park avenue

there is a special tool for this job but I have cheated on this but you ned to be careful when doing this.The wishbone shaped mount on the front going from motor to front of vehicle, remove and it allows the motor to tilt.

SOURCE: how to remove motor from 1999 buick park avenue

Fig. Fig. 1 Engine mounting-Vin C engine


Fig. Fig. 2 Front engine mount assembly-Vins L & 1 engines


Fig. Fig. 3 Front engine mounting bracket-Vins L & 1 engines

REMOVAL & INSTALLATION


CAUTION When draining coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze, and quite likely to drink any is is left in an uncovered container or puddles on the ground. This will prove fatal in sufficient quantity. Therefore, drain coolant into a sealable container. Coolant should be reused Unless it is contaminated or several years old. The epa warns that prolonged contact with used engine oil may cause a number of skin disorders including cancer. You should make every effort to minimize your exposure to engine oil. Protective gloves should be worn when dealing with engine oil. Wash exposed skin immediately after contact with oil with soap and water, or waterless hand cleaner.
3.8L VIN C Engine

1. Disconnect the negative battery cable. Using a scribing tool, matchmark the hood hinges and remove the hood.
2. Label and disconnect the air flow sensor wiring. Depressurize the fuel system.
3. Remove the air intake duct. Remove the throttle cable and bracket from the throttle body. Place a clean drain pan under the radiator, open the drain **** and drain the cooling system.
4. Raise and safely support the vehicle.
5. Remove the exhaust pipe-to-exhaust manifold bolts and separate the exhaust pipe.
6. Remove the engine mount bolts.
7. If equipped with a driveline vibration absorber, remove the bolts and disconnect the absorber.
8. Label and disconnect the electrical connectors from the starter. Remove the starter-to-engine bolts and the starter.
9. If equipped with air conditioning, remove the compressor mounting bolts and position aside. Do not discharge the system or disconnect the refrigerant lines.
10. Place a pan under the power steering gear. Disconnect the hydraulic lines and drain the fluid. Use a length of wire to hold the hoses aside.
11. Remove the lower transaxle-to-engine bolts.

1. Remove the flywheel cover. Matchmark the flexplate-to-torque converter relationship to insure proper alignment upon installation. Remove the flexplate-to-torque converter bolts.
2. Remove the engine support bracket-to-transaxle bolts and the bracket. Lower the vehicle.
3. Attach an engine hoist to the engine lift brackets and support the engine.
4. Remove the radiator and heater hoses from the engine and position them aside.
5. Label and disconnect the hoses from the vacuum modulator and canister purge lines.
6. Label and disconnect the engine electrical wiring harness(es) and position them out of way.
7. Remove the upper transaxle-to-engine bolts.
8. Carefully remove the engine from the vehicle.

1. Install the engine in the vehicle.
2. Connect the reposition the engine electrical wiring harness, secure the bracket.
3. Connect the hoses to the vacuum modulator and the canister purge lines.
4. Install the radiator and the heater hoses.
5. Remove the engine hoist. Raise and safely support the vehicle.
6. Replace the engine support bracket-to-transaxle bolts.
7. Replace the upper transaxle-to-engine bolts. Install the engine mount bolts and tighten to 70 ft. lbs. (95 Nm).
8. Install the torque converter and tighten the bolts to 46 ft. lbs. (62 Nm). Replace the flywheel cover.
9. Install the lower transaxle-to-engine bolts, tighten to 55 ft. lbs. (75 Nm).
10. Connect the power steering hydraulic lines to the power steering gear.
11. Install the air conditioning compressor, if equipped.
12. Install the starter and tighten the mounting bolts to 35 ft. lbs. (47 Nm).
13. Connect the electrical connections at the starter motor.
14. Connect the driveline vibration absorber, if equipped.
15. Install the exhaust pipe and replace the exhaust pipe-to-manifold bolts.
16. Lower the vehicle.
17. Connect the air flow sensor wiring. Install the hood assembly.
18. Connect the negative battery cable. Refill the cooling system.
19. Start the engine, allow it to reach normal operating temperatures and check for leaks.

SOURCE: 2000 Buick Park Avenue Service engine soon light

need to take car somewhere to have the code read with a scanner,try parts stores first some will do it for free if not the dealers have them

SOURCE: 1999 buick park avenue ultra motor mount and

1. Remove the engine mount to engine mount bracket nuts. Important: Ensure that the wood block extends past the width of the oil pan in order to avoid damage.
2. Use a jack with a block of wood on the jack under the oil pan in order to support the engine.
3. Remove the engine mount bracket front upper and lower nuts.
4. Remove the engine mount bracket front upper and lower studs and spacer.
5. Lower the engine as necessary and rotate the tensioner to remove the drive belt.Remove the supercharger belt.
6. Reverse For INSTALATION