2-3 shift solenoid circuit

Hello. Your vehicle has a shift solenoid electrical circuit malfunction; that solenoid is not 'energizing' properly, causing rough to no shift conditions. Good luck and keep me informed; if you want to.

P0758 Shift Solenoid B Electrical
P2761 Torque Converter Clutch (TCC) Pressure control (PC) solenoid control circuit.

OBD II Trouble Codes Home

P0758 Problem in Shift Solenoid Valve B Circuit
Fault :
Solenoid Valve 2 B - Open or Short to Earth or B+
Cause:
Wiring/Connectors from/to Solenoid Valve 2 Open or Short to earth.
Solenoid Valve 2 (N89) faulty.
Engine control module (ECM)/Powertrain control module (PCM)/Transmission control module (TCM)

Solutions:
Check/Repair Wiring/Connectors from/to Solenoid Valve 2.
Check/Replace Solenoid Valve 2.

Shift solenoid B electrical, transmission .Any problem with shifting,any after market electrical[starter,alarm].

P1782 DODGE - 2/4-OD Pressure Switch Circuithttp://engine-codes.com/p1782_dodge.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty 2/4-OD Pressure Switch
- 2/4-OD Pressure switch poor electrical connection
- 2/4-OD Pressure switch circuit is open or shorted
Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Transmission shift shockP1782 DODGE Description The pressure 2/4-OD Pressure Switch is part of the pressure switch of the transmission. The pressure switch are located in the solenoid assembly. The switch provide input information to the Transmission Control Module (TCM). The switch will inform to the TCM is pressure exist in a specified hydraulic circuit. the TCM uses this information to verified that the solenoids are working or not.
P0755 DODGE - 2/4 Solenoid Circuithttp://engine-codes.com/p0755_dodge.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty 2/4 solenoid valve
- 2/4 solenoid valve harness is open or shorted
- 2/4 solenoid valve circuit poor electrical connection
P0700 DODGE - Transaxle Control System Malfunctionhttp://engine-codes.com/p0700_dodge.htmlForum CodePossible causes- Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module Tech notes Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem.
Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transaxle shifting problems

Hello, all these codes are transmission related.
P0740 Torque Converter Clutch Circuit Malfunction
P0753 Shift Solenoid A Electrical
P1860 - TCC PWM Solenoid Circuit - Electrical
If any of solenoids have picked up some debris, or tiny pieces of metal from worn transmission componets, they will often set a fault code. Just something to keep in mind.

I hope this helps.

CODE PO758 - AUTOMATIC TRANSAXLE SHIFT SOLENOID B CIRCUIT FAULT.

All these code's are to your transmission, your mech needs to do more then pull code's, he needs to look at date on sensor to transmission before opening.

P0740 - Torque converter clutch solenoid circuit

P0758 - Shift solenoid (B) electrical

P0785 - Shift timing solenoid

P0761 - Shift solenoid (C) performance or stuck off

I would try Trans - X first pores right in to trans.

CODE PO758 IS A/T 2 - 3 SHIFT SOLENOID CIRCUIT 4T40 -E OR 4T45 -E CONDITIONS. THE 2 - 3 SHIFT SOLENOID IS DAMAGED OR HAS FAILED.OR CHECK THE ERLS FUSE.