2006 jeep liberty 3.7L
SOURCE: 2005 jeep liberty diesel code # p0101 map- sensor out of range what is map
The MAP sensor (MANIFOLD ABSOLUTE PRESSURE) changes voltage or frequency as intake manifold pressure changes (air flow increases or decreases). The engine's computer uses the reading to advance or ****** engine timing. On older, non-fuel injected engines the vacuum advance on the distributor did basically the same thing.
The MAP sensor also works with other sensors on the Jeep engine, specifically the Throttle Position Sensor (on the throttle body) and Crank Position Sensor (on the transmission bell housing) to control other fuel flow and ignition timing functions.
If you're having problems with the MAP sensor, or are getting a Check Engine light and code for the MAP sensor keep in mind that other problems may cause that error code.
Bad vacuum hoses, vacuum leaks, bad EGR valves, intake manifold leaks, clogged air filter can all affect the MAP. sensor. To know for sure all the other sensors should be checked for correct voltage and perimeters
Also, if you have done any mods to the engine, especially intake, exhaust and ignition mods you may get an error code for the MAP or incorrect reading and a resulting loss in power or increased fuel usage.
The map sensor is easy to change with a couple screws off the Throttle body.. The part the air inters (the air breather). Buy one from the auto parts store if your sure that is the problem and just replace it..There is no adjustments to it...
It really sounds to me that you have a small vacuum leak in a line somewhere.You can try spraying the motor vacuum lines with soapy water with the vehicle running to find a leak. Also listen and feel under the dash for leaks and hissing sounds.
Hope this helps.......
SOURCE: i have a 2006 jeep liberty and three lights are staying lit and
You need to take the jeep to a dealer or a good mechanic who can retreive the codes out of the computer. You may have a module problem but I will not guess without knowing the codes.
SOURCE: need a tail light wiring diagram for 2005 Jeep Liberty
I advice you don’t cut into the wiring harness but get the proper kit that is plug and play.
SOURCE: 2002 jeep liberty interior fuse diagram
1-20amp-pwr outlet frt. 2-10amp-rear fog lights(export only)
3-15 amp-horn 4-10amp-hedlt low beam rt
5-10amp-hedlt low beam lft 6-20amp-bodycontrolmodule/pwr dr locks 7-spare 8-spare 9-10amp- rt pk lt /rt tail lt/trailer tow lt/cluster
10-spare 11-15 amp-flasher 12-15 amp-stop lts
13-10amp-bodycontrolmodule/cmtc/cluster 14-spare
15-10amp-pdc fuel pmp & auto shutdownrelays/skis
16-20amp-pwr outlet rear 17-15amp-rear wiper 18-20amp-radio choke relay 19-20amp-frt fog lts/trailer tow stop and turn lts
20-20amp-sunroof 21-spare 22-10amp-wiperswitch/frt and rear washer 23-10amp-lft park lt/lft tail lt 24-10amp-pdc blower motor relay 25-10amp-heatseatswitch/hvac controlhead/trailor tow battery charge 26-10amp-hedlt highbeam rt 27-10amp-hedlt highbeam lft
28-spare 29-15amp-heated seat module 30-10amp-heated mirrors/rearwindowdefrosterindicator 31-20amp-cigarlighter
32-10amp-radio/frtdoorlockswitches/bodycontrolmodule
33-10amp-skis/diagnostic connector 34-15amp-cluster/courtesy lts/radio/bodycontrolmodule/maplights/cmtc/underhood lt/vanity lts
35-spare 36-10amp-ignition run/start-orc/lft and rt siacm
37-10amp-ignition run only-orc 38-10amp-abs module/brake shift interlock solenoid 39-10amp-rear window defroster relay/flasher/backup lts
134 views
Usually answered in minutes!
×