How to repair code P1633 in a 2010 crown victoria

Ford Crown Victoria Police Interceptor,

https://www.google.com/search?q=%E2%80%8BFord+Crown+Victoria+Police+Interceptor+canister+vent+valve+diagram

..

Ford Crown Victoria Questions - what would cause a whole ...

www.cargurus.com > Questions > Ford > Crown Victoria
CarGuruswhat would cause a whole car vibration when going between 48 and 65 mph, even ... Asked by Dfranz Aug 29, 2013 at 11:53 AM about the 2001 Ford Crown Victoria Police Interceptor ... You have an open diff by turning one wheel the driveshaft should turn before the .... 2007 Ford Crown Victoria Police Interceptor For Sale.

The police package interceptors had a common problem with the fans seizing up. There was a TSB ford released to correct the issue which called for the replacement of the electric fan assembly with an updated fan assembly.

Notorious for intake leaks, the composite plastic intakes crack and leak coolant-as to the lack of power, you mght have overheated it and done some damage to the engine. There was a recall (information below) for the 4.6 for the intake-the overheating and lack of power means you should at least have compression checked and go from there-you may have bad head gaskets or worse. Do a compression test before you do anything else.

Ford Motor Company will extend the recall (01M02) on 4.6L V8 equipped vehicles with plastic intake manifolds. Some of the composite intake manifolds used on 4.6L SOHC engines may develop fatigue cracks at the coolant crossover duct. This condition could result in engine coolant leakage which, if not serviced, may cause engine overheating. Complete loss of coolant may result in engine damage or engine failure.
The updated recall now includes:
• Certain 1996 through 2001 Model Year Crown Victoria Police Interceptor
• Certain 1998 through 2001 Model Year Crown Victoria with Taxi
• Certain 1998 through 2001 Lincoln Town Car Limousine and Livery Prep Package
• Certain 1996-2001 Crown Victoria Taxis, Police cars and Lincoln Town Car Limousine and Livery cars.
• Certain 1996 through 1997 Crown Victoria Police Interceptor Vehicles with 4.6L SOHC engines built at the St. Thomas Assembly Plant from the beginning of production for the 1996 Model Year through January 28, 1997.
• Certain 1998 through 2001 Crown Victoria Police Interceptor Vehicles with 4.6L SOHC engines built at the St. Thomas Assembly Plant from November 22, 1997 through December 15, 2000.
• Certain 1998 through 2001 Crown Victoria Taxi Vehicles with 4.6L SOHC engines built at the St. Thomas Assembly Plant from November 22, 1997 through December 15, 2000.
• Certain 1998 through 2001 Lincoln Town Car Limousine Prep Package and Livery Vehicles with 4.6L SOHC engines built at the Wixom Assembly Plant from November 22, 1997 through December 15, 2000.

1998 Crown Vic, is it a former police vehicle?

If the stoplamps are on continuously, the following may be at fault:

1. Circuitry.
2. Brake pedal position (BPP) switch.
3. Multifunction switch (Crown Victoria equipped with the police street appearance package or Grand Marquis)

CHECK THE BRAKE PEDAL POSITION (BPP) SWITCH
Disconnect: BPP Switch. Do the stoplamps continue to illuminate? If yes, continue to the next step. If no install a new BPP Switch.

CHECK CIRCUIT 511 (LG) FOR SHORT TO POWER
Disconnect: Central Junction Box (CJB) Fuse 14 (20A). Do the stoplamps continue to illuminate? If yes, and your Crown Victoria is equipped with the police street appearance package or Grand Marquis, continue to the next step. If Crown Victoria, REPAIR circuit 569 (DG). TEST the system for normal operation. If no, REPAIR the circuit. TEST the system for normal operation.

CHECK CIRCUIT 9 (LG/OG) FOR SHORT TO POWER
Disconnect: Multifunction Switch C202c. Does the LH stoplamp continue to illuminate? If yes, REPAIR the circuit. TEST the system for normal operation. If no, go to next step.

CHECK CIRCUIT 5 (OG/LB) FOR SHORT TO POWER
Disconnect: Multifunction Switch C202c. Does the RH stoplamp continue to illuminate? If yes, REPAIR the circuit. TEST the system for normal operation. If the high mounted stoplamp continues to illuminate, REPAIR circuit 569 (DG). TEST the system for normal operation. If the high mounted stoplamp does not continue to illuminate, INSTALL a new multifunction switch. TEST the system for normal operation.

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

MOST INTERCEPTER CARS, MEAN THEY HAVE AN ADDED GEAR IN THE TRANSMISSION! WHAT YOU'LL BE DOING IS GOING TO A TRANSMISSION WITHOUT THAT EXTRA GEAR! TO ANSWER YOUR QUESTION: YES YOU CAN REPLACE IT WITH A REGULAR TRANSMISSION! YOU JUST WON'T BE ABLE TO CHASE BURGLARS! HAHA

Manual--Helm.com

Firing order is 1-3-7-2-6-5-4-8 Passenger side of engine starting at front and going back is 1-2-3-4 Driver's side starting at front going back is 5-6-7-8.

Go to online store reliable they have repair manuals I am sure you will get the solution.
Here's the link
Best Manuals