Question about 1992 BMW 3 Series

Open Question

Cylinder head torque setting toyota avensis - 1992 BMW 3 Series

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 5 Answers

SOURCE: 1992 BMW Cylinder head

30nm 90 degrees, 90 degrees Renew bolts!!

Posted on Jun 20, 2008

Ad

johnz1313

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

steve_e_uk

steve morris

  • 1675 Answers

SOURCE: CYLINDER HEAD TORQUE SETTINGS BMW 318TI THANKS

hi this has to be done in 3 stages, leaving 20 to 30 minutes between tightening's they are as follows..
stage 1: 30Nm leave 30 minutes stage 2: 90 degrees turn leave 20 minutes stage 3: 90 degrees turn leave 20 minutes
you have to leave them this length of time so as not to put to much strain on the head in one go...hope this helps please vote thanks

Posted on Mar 21, 2010

niq niq

  • 54 Answers

SOURCE: cylinder head torque settings for 1989 bmw m5

60lbsft

Posted on Mar 31, 2010

greg benton

  • 231 Answers

SOURCE: cylinder head torque settings bmw

Hi dear40,

The m43 engine should be similar to both the m42 and m44. The cylinder head torque settings are 22ft/lb and 90degree torque angle, and another 90 degree torque angle. Make sure to wait approximately 10minutes before performing the 2nd torque angle.

Posted on Jun 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will u please help me with cylinder head and cam shafts torque specs for 2013 1.3 toyota corolla 1nr engine


(1) Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.
f050595e03-5f1mvaj5g1pcfjy4nobxv3ia-4-0.png (2) Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration. Torque:
70 N·m {714 kgf·cm, 52ft·lbf} (c) Mark the front of the cylinder head bolts with paint.

a098364e01-5f1mvaj5g1pcfjy4nobxv3ia-4-1.png (d) Further tighten the cylinder head bolts 90° as shown in the illustration.
(e) Check that the paint mark is now at a 90° angle to the front. cam bearing caps; Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

a098174e07-a-5f1mvaj5g1pcfjy4nobxv3ia-4-3.png Torque:
No. 2 Bearing cap -
30 N·m {301 kgf·cm, 22ft·lbf}
No. 3 Bearing cap -
9.0 N·m {92 kgf·cm, 80in·lbf}

Feb 23, 2018 | Toyota Cars & Trucks

1 Answer

How to replace cylinder head on 1996 RAV4


William, Could not a lot on your particular engine, links below to show the basics on removal/install of cylinder head. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
TOYOTA AVENSIS ENGINE REPAIR BLOWN HEAD GASKIT
How to replace the cylinder head gasket on 96 Toyota Camry 4 cylinder
Replacing the head of VVTI celica engine 2000 2005


Jul 09, 2016 | 1996 Toyota RAV4

1 Answer

Torque settings of cylinder head toyota quantum 2.7 vvti petrol


Cylinder head cover sub-assy x Cylinder head sub-assy 9 92 80 in.?lbf

Cylinder head sub-assy x Cylinder block sub-assy 1st - 39 398 29

Feb 12, 2016 | Toyota Cars & Trucks

1 Answer

Toyota 2c. I need cylinder head and flywheel Torque settings


Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.


Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

Aug 06, 2014 | Cars & Trucks

1 Answer

Toyota 5afe head bolts torque


Toyota 4A/ 5A-FE Cylinder Head Torque:
(a) Apply a light coat of engine oil on the threads and under the heads of the cylinder head bolts.
(b) Install the plate washer to each cylinder head bolt.
(c) Install and uniformly tighten the ten cylinder head bolts in several passes in the sequence.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)
HINT: Cylinder head bolts are in length of 90 mm
(3.54 in.) and 108 mm (4.25 in.). Install the 90 mm
(3.54 in.) bolts (A) in intake manifold side positions.
Install the 108 mm (4.25 in.) bolts (B) in exhaust
manifold side positions.

Mar 31, 2014 | 2003 Toyota Corolla

1 Answer

I need torque settings for engine 15B/F 4104cc


Check out the help links mentioned below:----
Cylinder Head Torque Setting http://schematicsdiagram.blogspot.com/2012/10/cylinder-head-torque-setting.html
----------- Lexus LS400: Transmission or Torque Converter? http://technoanswers.blogspot.in/2012/04/lexus-ls400-transmission-or-torque.html

----------
For more help.keep updated.
Thanks.

Oct 15, 2012 | Toyota Cars & Trucks

1 Answer

Cylinder head 2.4 torque


step 1 58 ft lbs.

step 2 additional 90 degrees

1_10_2012_5_41_54_pm.jpg

Jan 10, 2012 | 2003 Toyota Camry

1 Answer

I need the torque settings for a Toyota Corolla 1995 model 4afe engine TORQUE SETTINGS FOR THE CYLINDER HEAD? PLEASE PLEASE HELP


cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Feb 22, 2011 | 1995 Toyota Corolla

1 Answer

Head bolt tourqe settings on a toyota cressida


Cylinder head bolt removal sequence


Removal sequence: Front 3 7 11 13 10 6 2 1 5 9 14 12 8 4

***CAUTION*** The above sequence must be followed during removal as to avoid warpage of the cylinder head unit

Reverse sequence to install, Step 1: Torque to 10 Ft/Lbs Step 2: Torque to 18 Ft/Lbs Step 3: Torque to 25 Ft/Lbs Step 4: Turn an additional 90 degrees Step 5: Turn an additional 90 degrees Step 6: Torque the 2 recessed 8mm bolts to 13 Ft/Lbs *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper Torque

Don't forget to rate this answer, Good Luck

Apr 24, 2010 | 1992 Toyota Cressida

Not finding what you are looking for?
1992 BMW 3 Series Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

70 Answers

Doberman

Level 2 Expert

261 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...