Question about 2001 Oldsmobile Alero
By the timing belt cover:
Posted on Jun 28, 2009
It should be on the passenager side where the drive belts are try these websites to see if they have your car listed www.autozone.com and www.alldatadiy.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car.i also would like to give you this information if you every have any hard to find GM-parts its Schram auto & truck parts 1-800-292-1032 and they website is www.schramauto.com
Posted on Jun 28, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Removal & Installation
Exhaust manifold, if equipped with n automatic transaxle Right front wheel Splash shield Water pump sprocket access plate from the timing cover
Fig. Remove the water pump sprocket access plate from the timing cover -2.2L engine
Sprocket to water pump bolts Engine block to water pump bolt Engine front cover to water pump bolt Thermostat housing to water pump feed pipe 2 water pump to engine block bolts Water pump
Fig. Water pump mounting-2.2L engine
Water pump and bolts Thermostat housing to water pump feed pipe Engine front cover bolt and engine block to water pump bolt. Tighten the bolts to 15 ft. lbs. (20 Nm) 2 of the water pump sprocket to water pump bolts
Last water pump sprocket to water pump bolt and tighten the sprocket bolts to 89 inch lbs. (10 Nm).
Water pump sprocket access plate to the timing cover and tighten the bolts to 89 inch lbs. (10 Nm) Splash shield Right front wheel Exhaust manifold, if removed
WARNING Do not rotate the flex coupling more than 4 degrees or damage may occur. Oxygen Sensor (O 2 S) electrical connector Exhaust manifold heat shield Coolant inlet housing bolt through the exhaust manifold Exhaust manifold brace-to-manifold bolt Manifold-to-exhaust pipe studs Coolant inlet housing-to-water pump cover bolt Exhaust pipe from the exhaust manifold by pulling it downward Coolant inlet pipe from the oil pan Brake vacuum pipe from the camshaft housing Exhaust manifold from the cylinder head Heater hose from the heater outlet pipe Timing chain cover and tensioner Water pump cover-to-engine bolts 3 water pump-to-timing chain housing nuts Water pump and cover assembly Water pump cover from the pump
Fig. Exploded view of the water pump mounting-2.4L engine
Posted on Oct 22, 2009
If your water pump is leaking, then it will have to be replaced. This is not a job for the beginner as you will have to rmove the timing chain cover, harmonic balancer and timing chain. If you tackle this job your self make sure you mark your valve gears, crank and replace the chain exactly the way you removed it or your timing will be off.
Posted on Dec 11, 2009
I suggest that you visit the autozone.com website and register the vehicle. It doesn't cost anything and will give you access to an online repair manual. The steps for replacing the water pump should be available there. Hope this helped and best wishes.
Posted on Sep 01, 2009
you need a haynes repair manually.because you have to remove timing chain cover. you have to remove timing chain tensioners.to unload timing chain.because water pump is going to interfere with timing chain housing.you will need a manually . too much to tell you in words.
Posted on Mar 22, 2009
Tips for a great answer:
Oct 16, 2014 | 2004 Oldsmobile Alero
Apr 16, 2014 | 2002 Oldsmobile Alero
Nov 28, 2012 | 2001 Oldsmobile Alero
Jun 27, 2011 | 2002 Oldsmobile Alero
Remove the negative battery cable. Using a screwdriver, loosen the screw that connects the negative battery cable to the battery post. Pull the cable away from the post.
Lift th car using a jack. Support the Oldsmobile Alero with jack stands and the engine using a lift or some other engine support device.
Drain the Oldsmobile Alero's colling system by opening the cap on top of the radiator and unplugging the drain plug underneath the radiator. Position a large container under the drain hole to catch the draining coolant.
Disconnect the components that lead to the water pump with an adjustable wrench Lay them out in the order removed. In order, these parts include the automatic transaxle (if equipped), front wheel on the right side, splash shield, water pump sprocket and the access plate to the timing cover.
Use the access plate bolts to secure the water pump sprocket holding tool to the engine cover. Remove the pump bolts, front cover, thermostat housing, water pump feed pipe and two engine bolts using the adjustable wrench. Lift off the water pump.
Remove the bolts that secure the water pump to the block. Take off or scrape away the gasket. Remove and discard the o-ring between the water pump inlet pipe and the pump.
Spread a small amount of sealant on the water pump, on the areas where it mounts to the engine. Place the gasket on the sealant. Position the water pump onto the engine.
Insert the new bolts into the water pump. Torque the bolts to 89 inch pounds torque. Reconnect the other components in the order removed using an adjustable wrench.
Re-insert the drain plug into the radiator. Remove the engine support and jack stands. Lower the Olsmobile Alero to the floor.
Refill the radiator with coolant according to the instructions in your owner's manual. Screw on the radiator cap. Attach the negative battery cable to the post. Close the hood and test the car.
Nov 30, 2010 | 1999 Oldsmobile Alero
Oct 26, 2010 | 1999 Oldsmobile Alero
Nov 07, 2009 | 2003 Oldsmobile Alero
Sep 01, 2009 | 2002 Oldsmobile Alero
Jun 02, 2008 | 1999 Oldsmobile Alero
7,293 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: