Unable to pull out rear axle to change brearing

To change the bearing , you have to pull the axle. Jack the rear end up and use support jacks. Remove the differential cover, oil will come out. Put the transmission in neutral. Spin the differential until you see the bolt that holds the center pin, remove both. remove the tires. push the axle in. remove the clip one the end of the axle in the differential. pull the axle out. You can chisel the bearing out. But they do have tools that get them out.

pull rear cover, pull center pin bolt out, pull pin, push axle in to drop clip, pull axle out, remove old seal, install new one and reverse above

This is caused by a leaking rear axle seal you will need to pull the left rear axle out and change the seal and check for a worn axle bearing, this requires the removal of the differential cover, pin and center block or posi spring and clutch pack (if so equipped) and spider gears and then the "C" clip that retains the axle into the gear carrier, u will need a tube of silicone to reseal the cover and a axle seal installer tool and about 2 hours of your time

if it has the four bolts that have a flange piece on it also then its just a unbolt and pull one.another sign of the unbolt/pull type is there is no removable cover on the back of the diff. i never undo nothing but the 4 bolts. i leave twn in but real loose so when i yank on the axle it wont break nothing when it cuts loose all of a sudden.

take off the wheel and check to see if the axle is bolted to the rear end or poss have to take off the diff cover to take the axle hold down clips off then pull out the axle pull out the seal reinstall new one

replace the axle seal to replace pull the rear cover draining the gear oil then rotate the carrier around till the small bolt holding the carrier pin remove bolt pull pin out don"t turn carrier after pulling the pin push the axle in and remove the clip from the inside of the carrier that pin holds the axle clips in place after pulling out you can remove the axle then just pop the seal out and install new one use a socket or something that is the same size as the seal lube the axle and slide axle back in lift up when almost all the way in the tube putting it in the carrier once in replace clip and pullout on the axle thats it pretty much hope this helps you out

you have to block up the rear end then pull the cover off the rear end then pull tires and drums off then
go to the punkin and pull the center pin out its a 5/16 or 8mm bolt out slid the pin out then push axles in take the C-clips out then pull axles out
you will need a axle slide hammer to get the bearing out and
then tap the new one in just far enough to get the cyl. in
then put all back to gether

The Cheapest you can Get is @ A Pick A Part or Pull A Part, These are Auto Salvage yards that
You Go to With Your Tools And YOU REMOVE the Parts Yourself and they Charge VERY VERY REASONABLE Price for ALL PARTS. they Have Web sights that Tell All LOCATIONS.

Im Looking at Pull A Parts PRICE LIST and It Shows REAR AXEL'S DIFF COMPLETE for
DRUM BRAKE TYPE AXEL is $68.19 And DISC BRAKE TYPE Priced @ $73.87

http://www.indypickapart.com/contactus.html
Phone Number:
317.925.CARS (2277)
Unable to Find Other LOCATIONS uther than Indianapolis BUT, There May Many More
_________________________________________________________________________
NOW Pull A Part Does Have a Page for there Other Locations Try These Links
http://www.pullapart.com/

http://www.pullapart.com/Locations/Main.aspx

rear axle bearings I assume? Pull the diff cover, rotate the carrier so you can remove the pin from the center of the 4 spyder gears, push the axle in slightly, and remove large c clip from the carrier area. The axle will pull right out! These vehicles are hard on axle bearings. Look them all over.

Good Luck!

jack & support vehicle. remove rear axle cover drain fluid, removeleft rear tire drum/rotor brakes, remove bolt in axle housing that holds the 3/4 inch pin in place pull pin , push left axle shaft inwards and remove c clip from inside axle case,slide out axle shaft,remove seal,remove bearing and install in revers