How to check and add transmission fluid?

The automatic transmission fluid fill location on a 2008 BMW 650i can vary depending on the specific model and transmission type, but generally it is located under the hood and accessed through a dipstick tube.

To locate the dipstick tube for the automatic transmission fluid, follow these steps:

1. Open the hood of the vehicle and locate the transmission fluid dipstick. The dipstick handle is usually yellow, red, or black and is labeled with "ATF" or "trans."
2. Remove the dipstick from the tube and wipe it clean with a lint-free cloth or paper towel.
3. Reinsert the dipstick all the way back into the tube and then remove it again. The fluid level on the dipstick should indicate the current level of transmission fluid.
4. If the fluid level is low, you will need to add automatic transmission fluid. To add fluid, remove the dipstick and use a funnel to pour the fluid into the dipstick tube. Be sure to use the correct type of transmission fluid specified in your owner's manual.
5. Check the fluid level again with the dipstick to make sure it is at the correct level. Add more fluid as needed.

Note: It is important to follow the recommended procedure for checking and adding transmission fluid to your BMW 650i to avoid overfilling the system, which can cause damage to the transmission. If you are unsure about the location of the dipstick or how to properly add fluid, consult your owner's manual or a qualified mechanic for assistance.

Ah, for what vehicle?

Depends on your engine.

1980 JEEP CJ-7 2.5L 4-cyl Engine Code [B]
CAPACITIES
Engine, GM without filter..........2.4 quarts[1]
Wix Filter ........ 51040
Cooling System, Initial Fill..........8.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES
Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

Oilman

1. Check and add transmission fluid on a 2006 VW Passat with manual gearbox:




2. Check and add transmission fluid on a 2006 VW Passat with automatic gearbox:

In an automatic transmission, the dipstick should be located around back of the engine. You let the engine run to normal operating temp. and you check the fluid level, add as needed. You add through the dipstick tube with a funnel. Hope this helps.

If you are looking to check the fluid levels and add transmission fluid you will need to first purchase a fluid pump at your local car repair store. Most run between $10 and 25$. For best results, run your car for a few minutes to bring the fluids to operating temperatures before attempting to add fluid. Be careful of hot surfaces and liquids.
It is difficult to check the level of fluid in the 2001 Honda passport because it lacks a dipstick. Instead, you will have to get underneath the car and check it at the Automatic Transmission fluid pan. This is located approximately below the center of the rear passengers seat on the underside of the car.
To check the fluid, remove the top most bolt on the automatic transmission fluid pan (most use a 3/4 inch socket). Use your finger or other object to see if the fluid level is at the same level as the drain plug. This can be difficult to do therefore it may be easier to add fluid until it is full to verify that you are at the correct levels.
To add fluid, remove the top most bolt on the automatic transmission fluid pan (most use a 3/4 inch socket). Using the fluid pump, slowly add transmission fluid until it starts to drip out. Replace the bolt. Take care not to over tighten the bolt.
If you want to be thorough, start your car and while your foot is on the brake, run your transmission through the gears slowly. Turn off your car. Remove the fill bolt and check the fluid level again. If it is not full see the previous steps. If your levels are OK, replace the bolt and you are good to go.

Specifications Notes Use only Mercedes-Benz approved fluids

TYPE AF(DEXRON-II (R) Automatic Transmission Fluid) CAPACITY, Initial Refill*: 1982-85 190E 5.5 Liters 5.8 Quarts 1982-92 All w/V8 engines 7.7 Liters 8.1 Quarts 1986-91 190E, 260E, 300E 2.6L 6.0 Liters 6.3 Quarts 1986-91 300 Series 2.6L, except SL 6.2 Liters 6.6 Quarts 1990-91 300SL 6.0 Liters 6.3 Quarts 1992 600SEL 7.7 Liters 8.1 Quarts * Add specified quantity. With engine at operating temperature, shift transmission through all gears. Check fluid level in PARK, and add fluid as needed
diesel TYPE AF(DEXRON-II (R) Automatic Transmission Fluid) CAPACITY, Initial Refill*: 1984-89 190D Diesel 5.5 Liters 5.8 Quarts 1984-85 300 Series w/turbo 6.2 Liters 6.6 Quarts 1986-87 300 Series Diesel 6.2 Liters 6.5 Quarts 1990-93 300D Diesel 5.5 Liters 5.8 Quarts 1990-91 350SD, 350SDL Diesel 6.2 Liters 6.6 Quarts 1992-93 300SD Diesel 6.2 Liters 6.6 Quarts * With engine at operating temperature, shift transmission through all gears. Check fluid level in PARK, and add fluid as needed

use a very small funnel placed into the dipstick tube check frequently with the dipstick so you don't overfill

You add A/T transmission fluid at the same place you check it. 
Same place you check the A/T fluid level. You add fluid at the same location.