Question about 2008 Ford Focus SE Sedan

Open Question

How do i change the reverse light fuse on a ford focus 2008 zetec

Reverse light fuse

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 5 Answers

SOURCE: Replace driver side fog light Zetec model

remove under panels and fit ure new one

Posted on Oct 21, 2008

Ad
tneubauer

Thomas Neubauer

  • 437 Answers

SOURCE: after how many miles should the timing belt be changed

According to Ford the scheduled replacement is 120K

Posted on May 31, 2009

blubanshee

Corey Malone

  • 48 Answers

SOURCE: is it hard to change an alternator on a ford focus

Hello, This job is alot harder on your car than most that's for sure. It really depends on your mechanical ability and time vs the amount your willing to pay someone else. This job is easy if your not afraid to loosen the passenger motor mount and slid the engine forward about an inch with a pry bar. (Which sounds alot harder than it is) But the Hanes manual lists alot of things to do to get around the motor mount.

Per Haynes Manual.
Place Coolant Expansion Tank to one side.
Lift out Power Steering Reservoir and put to one side.
Remove DriveBelt.
Unscrew Wiring Loom bolt and move wiring to one side.
Remove Ground Cable from Strut Tower.
Bent the ground bracket down as much as possible.
Move Canister Purge Valve to one side.
Remove Plastic Cover from Alternator.
Unscrew and the alternator mounting bolt nearest the engine first.
Unscrew the other retaining bolt until it has fully disengaged from the bracket (not possible to remove bolt from alternator at this stage).
Lift the alternator out, Pulley side facing upwards.
Take care not to damage or you might screw your surrounding components!

I would say if you dont work on cars or have mechanical ability you should prob take it to a profesional. I hope my answer helped more than it scared you....lol....Have a great weekend and please rate my answer if you felt it was helpful

Posted on Jun 14, 2009

Anonymous

  • 5 Answers

SOURCE: 2003 ford focus zetec ABS light flashes on intermittently

an interminnent flash of the ABS light generally indicates a fault in the ABS system. It will flashing a code to you. Causes for this kind of problem are usually a sensor or air bag resistance out of range - too much, or not enough resistance. You might be able to find out on line what the code means. To read the code, they are generally groups of flashes. watch it carefully, there should be a big pause at some stage, that is the end of it's cycle. Now watch and count the flashes, for example- . . . - . . . . - . . - would be the code 342. If you have no luck finding the codes online i recommend calling your local ford dealership

Posted on Jun 14, 2009

super_guy

  • 1986 Answers

SOURCE: how do i change the fog light on a 2001 ford focus

lie on your back or jack the car up and reach up behind the bumper and pull the harness off the back of the bulb. twist the bulb counter clock wise and pull it out....

Posted on Sep 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

We’re is the reverse fuse on a 1999 gmc sierra


Reverse fuse ???? For transmission reverse or reverse (back-up light's )

Nov 07, 2017 | GMC Cars & Trucks

2 Answers

Fuse blows when put in reverse


Possibly an internal failure of the reverse switch. The blown fuse is for both the reverse and the turn signal lights. The fix is replacement of the reverse switch.

Sep 04, 2017 | Cars & Trucks

1 Answer

Reverse light and backing camera is not working. Might it be a fuse folt?? where could I find it?


check light bulbs are ok in reverse lights. Check wiring to reverse lights - see if they put a fuse at or near where they tapped power off reverse light.

Mar 07, 2016 | 2009 Nissan Murano

1 Answer

Fuse location reverse lights


hi. its usually on the lighting fuse but if your other lights are fine
then i would be looking at changing the reversing switch located
around. and near the gear leaver. good luck

Jan 27, 2014 | Toyota Cars & Trucks

2 Answers

Reverse lights not working


Check your reverse switch on the transmission to make sure its hook up . You will have to probably replace it . If you have not tried that first . Use a light meter to check the reverse switch if you have power at the plug then its the switch if theres no power then check your fuse box for blowen fuss

Oct 08, 2013 | 2007 Fiat Bravo 1.4

1 Answer

No reverse light, all fuse good. reverse Switch?


It's not that simple anymore . The transmission range sensor switch is what they have now . This range sensor informes the PCM - engine computer what gear the vehicle is in. When you put the gear selector into reverse B+ voltage from the range sensor to the PCM tells the PCM reverse has been selected , the PCM then will energize the reverse lamp relay (located in the under hood fuse/relay box) there by turning on the reverse lamps . There are two fuse's in the under hood fuse/relay box . F27 10amp. & F35 10amp.

Aug 11, 2017 | 2010 Ford Escape XLT

2 Answers

Reverse light dont work


No they should only come on when you put in reverse or else everyone would think you were backing up! its your bulb if just one, the fuse if both or the reverse switch indicator... Good Luck

Jan 21, 2013 | 2003 Chevrolet Tracker

1 Answer

My reverse lights don't work on my 2000 323CI 5 speed BMW when in gear


The fuse holder contains 10A fuse F27 which supplies power to the reversing light switch. When you shift into reverse with the engine running, the switch closes and the back up lights turn on. If the fuse is OK, you may have a defective switch

Oct 17, 2012 | BMW Cars & Trucks

2 Answers

Reverse and interior lights out, chevy express van


Fuse block under the hood. Driver's side, under the brake master cylinder. Number 18. TCB#2. Replace the fuse.

There is an under-engineered ground in the reverse circuit. If you back up with the dome lights on, it could blow that fuse. There should be some extra fuses under the cover of the fuse block.

Apr 25, 2010 | 2007 Chevrolet Express Passenger

1 Answer

My both reverse lights are not working on my peugeot 106 and one of the rear dipped lights has gone. is the reverse lights related to the fuse and the bulb could have gone on the rear dipped light?


There is a fuse for the reverse lights. If you find that the fuse is good, have the reverse light switch checked, it's usually on the side of the transmission.

Mar 10, 2009 | 1994 Oldsmobile Cutlass

Not finding what you are looking for?
2008 Ford Focus SE Sedan Logo

Related Topics:

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...