How do you replace wiper contdrol - 1999 Chevrolet Venture

video
http://www.bing.com/videos/search?q=2006+Buick+Rendezvous+Open+Question+Wiper+motor+replacement&FORM=HDRSC3


2006 Buick Rendezvous Open Question Wiper motor replacement Bing Videos

Under the air cleaner assembly towards the firewall it is the one on the left with the grey top and when faulty produces code of p0010 it is GM part number 12655 420

The wiper delay is in the steering column. It's a small box about 2 x 2 inches with a wiring harness attached. With the testing procedures I found below, you should be able to figure it out. I found wiper delays on eBay for around $10 to $20. Good luck.

WINDSHIELD WIPERS CHEROKEE, COMANCHE & WAGONEER 1. POWER INPUT Remove circuit breaker. Test battery side of circuit breaker. If battery voltage is not present, repair open to splice. Test across circuit breaker terminals. Tester reading should be zero (0) ohms. If not, replace circuit breaker. 2. GROUND Connector A unplugged. Test terminal G. Tester reading should be zero (0) ohms. If not, repair open to ground. 3. INTERMITTENT WIPERS Ignition switch in ACCY. Remove delay module and plug connectors together from the module. If wiper operate in LO and HI speed modes and mist (washer) is working, if wipers and mist operate, replace intermittent module. If not go to step 4. 4. WIPER/WASHER SWITCH Ignition in RUN, wiper switch position as indicated, back probe switch side of connector A for standard, connector B for intermittent: Test connector terminal E-wiper switch in LO and mist/intermittent. If battery voltage is not present, replace switch. test connector terminal C-wiper switch in HI. If battery voltage is not present, replace switch. Test connector terminal F-wiper switch to OFF. If battery voltage is present until wipers stop and then voltage drops to zero (0), system is working fine. If this does not occur, replace switch. 5. INTERMITTENT WIPERS Connector B unplug. Test across terminal A and D while rotating switch from minimum to maximum delay. If tester reading is not between 0-500 ohms, replace switch. Test across terminal A and G while rotating switch from minimum delay to maximum delay. If tester reading is between 0 and 500 ohms, replace wiper module. If not replace switch. 6. WIPER MOTOR Ignition in ACCY, wiper switch position as indicated, probe connector D. Test connector terminal 1. If resistance is no zero (0) ohms,repair open to ground. Test connector terminal 4-wiper switch in any position. If battery voltage is present, replace motor. if is not repair open from fuse panel. Test connector terminal 2-wiper switch in LO. If battery voltage is present, replace motor. If not , repair open from wiper switch. Test connector terminal 2-wiper switch in HI. If battery voltage is present, replace motor. If not , repair open from wiper switch. Test connector terminal 5-wiper switch OFF with voltmeter connected. If battery voltage is present until wipers stop and then voltage drops to zero, system is OK, replace motor. If not, repair open from wiper switch.






Found on the web. I hope this helps.
Rich Long

WINDSHIELD WIPERS

It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring: -----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below: -------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

These details will help.

Thanks.

It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below:-------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

These details will help.

Thanks.

It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below:-------

Complete wiper components replacing details ?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

These details will help.

Thanks.

It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function.If yes then fuse is ok,but issue is wiper motor.
If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----
For complete troubleshooting i suggest you few helpful links with accurate solutions.
-------------
Click the link below:-------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html
------------ How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------
These details will help.
Thanks.

For wiper problem,troubleshooting,check the help links provided below.Click the link to go through its procedure:----------------
HOW TO REPLACE A WINDSHIELD WIPER MOTOR

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

---------
Wipers not working, but hear relay click? http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html--------- Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

-----------------
How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html


------------
Where is wiper fuse located?

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html


-----------
Complete wiper components replacing details for Car Models? http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html The wipers not working? http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

How to Replace Wiper Blades Guide (Typical):
Potential tools needed to replace wiper blades:

• Flat blade screwdriver (small)
• Small nosed pliers
• Latex or vinyl gloves
• Safety goggles

To replace wiper blades theactual action of replacing the blade is no big deal, it's the locationof the blade down below the hood that can make it difficult though.Sometimes it helps to open the hood to gain access to the wiper blades.Other times it is helpful if the wiper blade is somewhere in the motionline of wiper action. The trick is to get the wiper to stop somewherein the wiper arc. Turn the wipers to the on position and allow thewipers to start, and then shut the key off when the wiper has arrivedin a desirable position on the windshield. To replace your wiper bladesplease follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.

• Step 1: With the hood closed, turn the wiperson, when the wipers are in the middle of their arc turn the key to theoff position. (Note: if this can't be done because of wiper conditionand you want to avoid scratching the windshield please open your hoodto gain access)
• Step 2: Locate the mounting clips at the top pivot on the wiper blade
• Step 3: Release the clip and remove the wiper arm
• Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
• Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:

• Make sure the wiper blades are the same size as the original blades.
• When replacing wiper blades not getting the blade onthe mounting pin completely allowing the wiper arm to become dislodgedand possibly causing damage to the windshield.
• Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
• Wiper blade can create a chattering noise when theblade is not properly balanced allowing the blade to "flop" back andforth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

How to Replace Wiper Blades Guide:
Potential tools needed to replace wiper blades:

• Flat blade screwdriver (small)
• Small nosed pliers
• Latex or vinyl gloves
• Safety goggles

To replace wiper blades the actual action of replacing the blade is no big deal, it's the location of the blade down below the hood that can make it difficult though. Sometimes it helps to open the hood to gain access to the wiper blades. Other times it is helpful if the wiper blade is somewhere in the motion line of wiper action. The trick is to get the wiper to stop somewhere in the wiper arc. Turn the wipers to the on position and allow the wipers to start, and then shut the key off when the wiper has arrived in a desirable position on the windshield. To replace your wiper blades please follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.

• Step 1: With the hood closed, turn the wipers on, when the wipers are in the middle of their arc turn the key to the off position. (Note: if this can't be done because of wiper condition and you want to avoid scratching the windshield please open your hood to gain access)
• Step 2: Locate the mounting clips at the top pivot on the wiper blade
• Step 3: Release the clip and remove the wiper arm
• Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
• Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:

• Make sure the wiper blades are the same size as the original blades.
• When replacing wiper blades not getting the blade on the mounting pin completely allowing the wiper arm to become dislodged and possibly causing damage to the windshield.
• Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
• Wiper blade can create a chattering noise when the blade is not properly balanced allowing the blade to "flop" back and forth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.