Location of crankshaft position sensor for 1996 madza protege

The service and repair manual with diagram will provide you step by step help to locate and fix the problem easily on your own and you will get the manual from the given link Home Toolsnyou

yes one of the fault codes
toss water on the CAS ..if hot see if the motor fires

signal comes from the ecu
could be faulty fuel pump /relay ?

1996 Dodge Truck Caravan 2WD 3.0L MFI 6cyl

The Crankshaft Position Sensor is located:Under hood, driver side, rear engine area, mounted top rear of engine .click here and enlarge picture,it's number 9,send picture to your library and you can enlarge even more.Here's the part.Here's how to remove.

CRANKSHAFT POSITION SENSOR LOCATED NEXT TO THE STARTER.

Click over image for zoom...



Fig. 1: View of the crankshaft position sensor and its location-1996 5.2L engine shown




Fig. 2: View of the crankshaft position sensor and its location-1996 4.0L engine shown


Removal & Installation
4.0L Engine

1. The CKP sensor is located on the transmission bellhousing. Disengage the sensor wiring connector and remove the sensor wiring hold-down clip from the fuel rail.
   
2. Remove the sensor mounting bolt and carefully pull the sensor out of the bellhousing.
   
3. Installation is the reverse of removal.

5.2L and 5.9L Engine

1. The CKP sensor is bolted to the top of the cylinder block near the rear of the right cylinder head. Disengage the sensor wiring connector and remove the two sensor mounting bolts.
   
2. Carefully pull the sensor out of the cylinder block.
   
3. Installation is the reverse of removal.

Hope this helps (remember to rate this answer).

The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine
Location of the crankshaft position sensor on the 3.0L engine
Location of the crankshaft position sensor on the 3.3L and 3.8L engines
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.

1. Disconnect the negative battery cable.
2. Raise and safely support the vehicle.
3. Disconnect the crankshaft position sensor electrical connector.
4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.

To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.

1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
2. Connect the crankshaft position sensor electrical connector.
3. Lower the vehicle.
4. Connect the negative battery cable.

1996 Volkswagen Jetta 2.0L SFI 4cyl
The Camshaft Position Sensor is located under hood, center, upper engine area, driver side of engine block, mounted in distributor.

This sensor performs the same function as a crankshaft position sensor; providing a signal to the ECM regarding the position of the crankshaft.

Although the camshaft position sensor is an essential input for the ECM to determine ignition timing, information on testing the sensor is located in of this guide (autozone.com / free register).

Hope help you; remember rated this help. Good luck.

under hood, center, upper engine area, mounted on upper driver side of engine.

Here you go:
Fig. 3: Crankshaft position sensor (1) is located next to the oil filter (2) on the 2.4L engine