Question about 1999 Dodge Neon

Open Question

How to install an alternator on a 1999 neon

What is the easiest way to get the alternator back onto the T-bolt on a 1999 dodge neon.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Timothy Sorenson

  • 41 Answers

SOURCE: 1999 Dodge Neon thermostat Installation

80113c0e.gif

Posted on Apr 26, 2009

Ad

Anonymous

  • 1 Answer

SOURCE: 1999 dodge neon 2door fireing order

i think it is 1 3 4 2
i got 99 dodge neon DOHC i downloaded the user manual from this link and believe me it helps a lot but you a pdf reader to open it
http://pdftown.com/PDF-Dodge-Neon-1999-Electronic-Service-Manual-ESM.html
by the way my car has 98000 miles on it and it drives more than perfect all it needs a new sound system mine works but i need something more so im looking for new radio/cd player but still don't which one fits so if you know any info please respond.
sincerely
G.Koussa

Posted on Jun 02, 2009

Anonymous

  • 18 Answers

SOURCE: 1999 dodge neon just stopped running. The engine

1. check ASD relay
2. check crank sensor, you may need to replace it

Good Luck

Posted on Jul 05, 2009

Gort007

Just Gort

  • 1187 Answers

SOURCE: I am changing the alternator in a 1998 dodge neon, need diagram

No diagram...
The pivot bolt is the long bolt that holds the alternator to the frame.
If you loosen it, the alternator can "swing" with the pivot bolt as its .... well, pivot, or swing center.

The long bolt must be removed completely in order to remove the alternator.

Be sure to doisconnect the negative cable from your battery.

Hope this hleps w/o a diagram.

Posted on Sep 14, 2009

techbuster

INDIRA KUMAR

  • 5081 Answers

SOURCE: 1999 Dodge Neon rear license Plate bulb

LICENSE PLATE LAMP BULB
REMOVAL

  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Posted on Oct 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Where is alternator located in the engine compartment?


Are these guys SERIOUS??


blueextc3221_1.jpg

The alternator is accessed from UNDER the vehicle LEFT SIDE facing the engine bay.

REMOVAL & INSTALLATION




1. Disconnect the negative battery cable.

2. Loosen, but do not remove the alternator adjusting nut.

3. Turn the front wheels completely to the right, then raise and safely support the vehicle.

4. Unfasten the retainers, then remove the plastic lower splash shield.

5. Unfasten the alternator field circuit wiring connector. You must squeeze the locking tab to release it.

6. Remove the B+ terminal nut and wire.

7. Loosen the alternator pivot bolt, but do not remove it.

8. Remove the alternator drive belt. The alternator spill shield does not have to be removed.

9. If necessary, remove the bottom pivot bolt and anti-rotation tab.

10. Unfasten the three mounting pivot bracket bolts, then remove the pivot bolt and bracket.

11. Holding the alternator in one hand, remove the adjustment nut then slide the alternator off the T-bolt. The T-bolt does not have to be removed. Lower the alternator and remove through the wheel well.

12. You may need to use a C-clamp to drive the sleeve into the mounting ear for installation clearance.

13. Position the alternator in the vehicle, sliding it onto the T-bolt. Install the adjusting nut.

14. Install the bracket and pivot bolt, then install the three mounting pivot bracket bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).

15. If removed, install the anti-rotation tab and bottom pivot bolt hand-tight.

16. Install the alternator drive belt.

17. Tighten the alternator pivot bolt to 40 ft. lbs. (54 Nm).

18. Install the B+ terminal wire and nut. Tighten the nut to 75 inch lbs. (9 Nm).

19. Attach the alternator field circuit wiring connector, making sure the locking tabs are engaged.

20. Install the splash shield, then carefully lower the vehicle.

21. Tighten the adjusting nut.

22. Connect the negative battery cable. Adjust the alternator belt.

Thanks!!

Feb 07, 2011 | 1998 Dodge Neon

1 Answer

How do you take the alternator off for a 96 plymouth neon


For REMOVAL & INSTALLATION check this procedure...
  1. Disconnect the negative battery cable.
  1. Loosen, but do not remove the alternator adjusting nut.
  1. Turn the front wheels completely to the right, then raise and safely support the vehicle.
  2. Unfasten the retainers, then remove the plastic lower splash shield.
  1. Unfasten the alternator field circuit wiring connector. You must squeeze the locking tab to release it.
  1. Remove the B+ terminal nut and wire.
  1. Loosen the alternator pivot bolt, but do not remove it.
  1. Remove the alternator drive belt. The alternator spill shield does not have to be removed.
  1. If necessary, remove the bottom pivot bolt and anti-rotation tab.
  1. Unfasten the three mounting pivot bracket bolts, then remove the pivot bolt and bracket.
  2. Holding the alternator in one hand, remove the adjustment nut then slide the alternator off the T-bolt. The T-bolt does not have to be removed. Lower the alternator and remove through the wheel well.
To install:
  1. You may need to use a C-clamp to drive the sleeve into the mounting ear for installation clearance.
  2. Position the alternator in the vehicle, sliding it onto the T-bolt. Install the adjusting nut.
  3. Install the bracket and pivot bolt, then install the three mounting pivot bracket bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  4. If removed, install the anti-rotation tab and bottom pivot bolt hand-tight.
  5. Install the alternator drive belt.
  6. Tighten the alternator pivot bolt to 40 ft. lbs. (54 Nm).
  7. Install the B+ terminal wire and nut. Tighten the nut to 75 inch lbs. (9 Nm).
  8. Attach the alternator field circuit wiring connector, making sure the locking tabs are engaged.
  9. Install the splash shield, then carefully lower the vehicle.
  10. Tighten the adjusting nut.
  11. Connect the negative battery cable. Adjust the alternator belt.

Hope helps.

Jul 16, 2010 | 1996 Plymouth Neon

1 Answer

I need to change the starter in my 2001 dodge neon


The starter is located under the car where the transmission and engine meet toward the front of the neon. The starter actually bolts up with face toward the transmission. You must get the car up on ramps or on a hoist to see the starter. This is just a general method; it is very hard to give words to describe some of the steps without pictures. Removal: Disconnect and isolate the battery negative cable. Raise vehicle on hoist. Remove starter bolts. Remove starter assembly. Disengage latch and remove solenoid connector from starter assembly. Remove battery positive connector from starter assembly. It is not necessary to remove the alternator output lead from the connector. Installation: Clean corrosion/dirt from the cable and wire terminals before installing wiring to the solenoid. Attach battery positive connector to starter. Ensure alternator output connector is snapped into the battery positive connector. Tighten the captive nut to 10 Nm (90 in. lbs.) . CAUTION: It is critical that the alternator output terminal be connected to the battery positive terminal of the starter solenoid, for proper operation of the charging and cranking systems. Install solenoid connector to starter. Ensure that latch is fully engaged. Position the starter face into transmission housing. Start bottom mounting bolt and thread in until bolt is snug. Attach ground cable to upper starter mounting bolt. Ensure the proper starter alignment before tightening the starter mounting bolts to 54 Nm (40 ft. lbs.) torque. Lower vehicle and connect negative battery cable.

Jul 13, 2010 | 2001 Dodge Neon

1 Answer

I have a 2003 dodge neon sxt and i can locate the alternator but i dont see how to take if off please help


To remove the alternator you will need to raise the front of the car and block the rear wheels. Disconnect the negetive wire from the battery. Loosen the upper alternator adjustment boltnut. Remove the right front tire and the accessory drivebelt splash shield. Loosen the alternator lower mounting bolt. Remove the alternator drive belt and disconnect the electrical connectors from the alternator. Remove the upper and lower adjustment bolts and remove alternator. You will have to remove the alternator bracket when you lower the alternator down. Installation is the reverse of removal. Hope this will help you.

May 16, 2010 | 2003 Dodge Neon

1 Answer

Need to change alternator belt on 2005 dodge neon.


First you need to take off the other belt. Turn the tentioner (2), usually a 3/8 ratchet, and remove the belt.

Second, you need to loosen the alt tension bolt, almost straight down from the (1). Push alternator toword motor and remove belt. Installation is the opposite.

Hope that helps

secureimgcontent.asp?sg=%7b37f4584d-540e-447a-bcf4-3a321aa90c73%7d&guid=c0019841

Feb 03, 2010 | 2005 Dodge Neon

2 Answers

I just need to know where the alternator is located on a 2004 dodge neon 2.0L SXT


Fig. View of the alternator after removing the splash shield - 2.0L engines

2f8e1a8.jpg

Removal & Install - 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Alternator jam nut, loosen only Alternator adjustment nut, loosen only Accessory drive splash shield Alternator lower bolt, loosen only Alternator drive belt Alternator field circuit wiring connector, push the RED locking tab to release Battery positive terminal Upper and lower bolts, move alternator off pivot bracket Pivot bracket Alternator

To install:
Install or connect the following:
Alternator Pivot bracket and torque the bolts to 40 ft. lbs. (54 Nm) Alternator, move it onto pivot bracket Alternator field circuit wiring connector, push RED locking tab in until it snaps in place Battery positive terminal Alternator drive belt Tension the drive belt to 100 lbs. (used) or 135 lbs. (new) Alternator adjustment bolt Alternator jam nut and torque nut to 40 ft. lbs. (54 Nm) Alternator mount bolts and torque the bolts to 40 ft. lbs. (54 Nm) Accessory drive splash shield
Negative battery cable

Fig. Alternator mounting-2.4L engine shown

d3b3dc1.jpg

I hope helps with this (remember rated this help) Good luck.

Jan 05, 2010 | 2004 Dodge Neon

1 Answer

Where is the pivot bolt i have loosened the 2 other bolts but still cant get the belt to tighten back up 98 dodge neon


You need to remove the pasengers side wheel an d some inner fender pieces to get at the botton alternator bolt,there is a nut on the other end that can be a problem if you're doing it alone.

Nov 06, 2009 | 1998 Dodge Neon

1 Answer

How to install alternator belt 2001 Dodge neon


Below is a diagram for the belts on your car. You will see to the right, an adjusting bolt. This loosens the tension to slide the belts on and off. Once the new belt is on, apply pressure to get the belt tight (a long flathead screwdriver or crowbar should do) and while tight, re-tighten the adjusting bolt.
da5dc36.jpg

Oct 18, 2009 | 2001 Dodge Neon

1 Answer

I am changing the alternator in a 1998 dodge neon, need diagram


No diagram...
The pivot bolt is the long bolt that holds the alternator to the frame.
If you loosen it, the alternator can "swing" with the pivot bolt as its .... well, pivot, or swing center.

The long bolt must be removed completely in order to remove the alternator.

Be sure to doisconnect the negative cable from your battery.

Hope this hleps w/o a diagram.

Sep 14, 2009 | 1998 Dodge Neon

1 Answer

Need to change the alternator


REMOVAL & INSTALLATION

3.3L Engine:
  1. Disconnect the battery negative - cable.
  2. Disconnect the alternator field circuit plug.
  3. Remove the B+ terminal nut and wire.
  4. Loosen the adjusting T-bolt, but do not remove it.
  5. Loosen the pivot bolt, but do not remove it either.
  6. Remove the alternator drive belt.
  7. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  8. Remove the mounting bolt.
  9. Remove the spacer & washer
  10. Remove alternator.
To install:
  1. Attachthe alternator to the support bracket. Tighten all bracket andalternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Connect the negative - battery cable.
-------------------------------------------------------------------------------------------------
3.5L Engine:
  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
  4. Loosen the belt adjusting bolt.
  5. Remove the alternator drive belt.
  6. Remove the bracket.
  7. Remove the lower mounting bolt and pivot bolt.
  8. Remove the alternator.
  9. Disconnect the alternator field circuit plug.
  10. Remove the B+ terminal nut and wire.
To Install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
If you need photos to follow then try this link...
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528006a83e

Jan 20, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
1999 Dodge Neon Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...