How to remove front bumper on fiat 500 ?

To remove the bumper cover on a 2002 Cadillac Escalade to access the license plate assembly, you'll need some basic tools and follow these steps:
**Note:** Be sure to take necessary safety precautions, and if you're uncomfortable doing this yourself, consider consulting a professional mechanic.
1. **Gather Tools and Materials:**
- Screwdrivers
- Socket set
- Pliers
- Trim removal tool (or flathead screwdriver)
2. **Raise the Vehicle:**
- For easier access, you can raise the front end of your vehicle using a jack and support it with jack stands.
3. **Remove the Wheel Well Liners (Optional):**
- Depending on your vehicle and access, you may need to remove the wheel well liners to reach the bumper attachment points. These are typically held in place with plastic clips or screws.
4. **Remove Retaining Clips and Screws:**
- Locate and remove the screws, clips, or fasteners holding the bumper cover in place. These are typically found along the top and sides of the bumper.
- Use a trim removal tool or a flathead screwdriver to carefully pry out the clips.
5. **Disconnect Fog Lights (if applicable):**
- If your vehicle has fog lights integrated into the bumper cover, disconnect the wiring harnesses.
6. **Detach the Bumper Cover:**
- Carefully start detaching the bumper cover from the vehicle by gently pulling it away. Work your way around the bumper to release the clips or fasteners.
7. **Remove the License Plate Assembly:**
- Once the bumper cover is loosened, you should have access to the license plate assembly.
- Remove the screws or fasteners securing the license plate assembly, and detach it from the bumper cover.
8. **Install the New License Plate Assembly:**
- Attach the new license plate assembly to the bumper cover, using the same screw holes or fasteners.
9. **Reattach the Bumper Cover:**
- Align the bumper cover properly, and carefully push it back into place, making sure it clips securely.
10. **Reattach Retaining Clips and Screws:**
- Put back the screws and retaining clips in their respective locations along the top and sides of the bumper cover.
11. **Reconnect Fog Lights (if applicable):**
- Reconnect the wiring harnesses for the fog lights.
12. **Reinstall Wheel Well Liners (if removed):**
- If you removed the wheel well liners, reinstall them and secure them with the clips or screws.
13. **Lower the Vehicle:**
- Carefully lower your vehicle from the jack stands if you raised it.
Remember to take your time, work carefully, and document the disassembly process if necessary. If you're unsure about any step, it's always a good idea to consult your vehicle's repair manual or seek professional assistance.

It comes out the front, remove the bumper and all the body parts then pull it out.

There are some steps that help you to easily remove Front Bumper :
1. Open the hood of your car.
2 . Look under the edge of the front of the car at the end of the bumper.
Pull the plastic shield down out of the way if it doesn't come off completely. Reach behind the bumper at each corner and you should find a bolt holding the corner of the bumper to the car. Remove these bolts. The bumper should come off.
For more details, click here at https://www.drivenbystyle.com/body-kits-aerodynamics/front-bumpers

If its a painted plastic bumper cover and everything underneeth is fine a body shop should only charge around 150 to $200

try it and find out

The starter is at the front of motor bottom of car directly behind radiator. You will need to remove the skid plate and go about 12 inches back from the bumper while under the car. The starter is a cylinder shaped and mounts to the bottom of the block in front of the oil pan.

Look behind you bumper where the lights are installed. There should be a clip slipped over the back of the housing that holds the light into the bumper. 1 per light. Use some needlenose plyers or a screwdriver to push it off. The light sould pull out of the bumper from the other side. You can disconnect the harness is you wish or just replace the bulb. Whichever suits your fancy. After replacement put the holder back into the bumper and slip the clip back on behind it. 10 minute job.

decorative [and possibly functional] license plate frames are available after-market from companies like www.jcwhitney.com. a local machine shop or welder could fabricate a 'backing plate' to reinforce the plate.

The sensor is behind the bumper reinforcement panel.

try using self tapping screws so you dont have to remove it, you can drill pilot holes if the screw wont go thru easy, and you dont need a nut/bolt