Question about 1993 Mazda Protege

1 Answer

The breakerbox for the lights inside the house keeps popping.

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 26 Answers

Something must be grounding somewhere

Posted on Feb 16, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the left cv axel from the the housing case of a 2005 ford escape split ring is keeping it from being removed


Enough force applied will pop it out. But you can't grab hold and yank-you might pull apart the cv joint. Shops can use a slide hammer with an attached fork that slips around the cv joint housing. Another method is using a large screwdriver or pry bar between the axle housing and the cv joint housing. Slip it between them and place tip of bar against the cv housing. Now give it a good stiff push with your hand to pop out the joint and axle. Be careful of the aluminum axle case and the axle seal-don't break or damage anything. Just remember: enough force applied will pop out the circlip from its groove inside the axle case.

Feb 12, 2013 | 2003 Ford Escape

1 Answer

My tail and brake lights keep popping fuses.


You might have a bad wirre in one of the tail light housings.they get corroded and rotten

Dec 03, 2012 | Cars & Trucks

1 Answer

Rear door latch is broke


I had to do this, too... Mine cost me $70 at the local dealer (they even got it in the same stock paint color). Tip: buy a few of the inexpensive replacement plastic pins for your inner panel when you buy the handle housing, as they tend to break easily. You can pop the old pins by sticking a narrow straight screwdriver or a butterknife under the panel near them and twisting... once it's off, the screws for the old handle housing are fairly easy to spot (just remember where the housing bolts on from the exterior are located). Now that those are off, realize that the thing is probably hanging from your trunk by the wires connecting the license plate lights and the handle, itself They can be removed from the old, broken housing with a phillips #2 (normal size) screwdriver, and then the wires have a quick-disconnect so that you can pop the lights and the handle off w/o cutting the wires. Pop them off, slide the wires through your new handle housing, and screw them back on. then slide the handle housing into position (lining up the screws that are molded into the housing with the adjacent holes). You'll have to kind of hold it in place as you raise the trunk hatch to full open position, but once it's up, gravity is your friend. Use the screws that were holding the parts from the broken housing to re-affix the new one, and you're done.

Feb 29, 2012 | 2006 Scion xB

1 Answer

How do I change a headlight bulb in 2008 prius


I just did this and it was a pain. There are several YouTube videos out there but nit real clear. First remove the cover to the fuse box. Then locate the light housing. The black plastic housing with fins needs to be turned counter clockwise about 3/4- 1 inch or so to pop off the housing. The problem is if the seals are dry it is almost impossible. Don't bang on the fins as they will break. I used wd40 along the top of the seals to penetrate the seals for about 20 min. Wipe up the excess as you don't want oil on any of the new bulbs. Mark the outside and inside of the housing with a scribe line to note your progress with the turn. Sometimes a vacuum will keep the housing from popping out. You can drill a very, very small hole in the housing to release the vacuum and them resell the hole with super glue. To remove the silver looking backing to the bulb you need to turn counter clockwise 1/8 turn and pull. There are two clips that are holding the bulb in place. Push down the side clips and move away from the housing to the outside. Once both clips are released it should rotate backward like a hinge away from the bulb. Replace the bulb with the new one and make sure the bulb is inserted with the long rod on the bottom. I just looked through the lens as I inserted the new bulb. Rotate the clip assembly forward a reattach the clips on each side and reattach the silver electrical connector and turn clockwise 1/8 turn to secure in place.
replace black plastic housing and rotate to align the scribed lines.
this works the same for both sides. However the right side, opposite the fuse box, has a black air box the needs to be removed first by popping up the round black poppet clip and then pull air box out of the way. Do not disassemble the from of the car to remove the light assembly. I saw this on YouTube and it was complicated and a mistake! Don't do it! To hard to reassemble!
good luck!

Apr 16, 2011 | 2008 Toyota Prius

1 Answer

Change headlight bulb toyota prius


I just did this and it was a pain. There are several YouTube videos out there but nit real clear. First remove the cover to the fuse box. Then locate the light housing. The black plastic housing with fins needs to be turned counter clockwise about 3/4- 1 inch or so to pop off the housing. The problem is if the seals are dry it is almost impossible. Don't bang on the fins as they will break. I used wd40 along the top of the seals to penetrate the seals for about 20 min. Wipe up the excess as you don't want oil on any of the new bulbs. Mark the outside and inside of the housing with a scribe line to note your progress with the turn. Sometimes a vacuum will keep the housing from popping out. You can drill a very, very small hole in the housing to release the vacuum and them resell the hole with super glue. To remove the silver looking backing to the bulb you need to turn counter clockwise 1/8 turn and pull. There are two clips that are holding the bulb in place. Push down the side clips and move away from the housing to the outside. Once both clips are released it should rotate backward like a hinge away from the bulb. Replace the bulb with the new one and make sure the bulb is inserted with the long rod on the bottom. I just looked through the lens as I inserted the new bulb. Rotate the clip assembly forward a reattach the clips on each side and reattach the silver electrical connector and turn clockwise 1/8 turn to secure in place. Reattach housing and turn clockwise to align scribe marks.

Apr 16, 2011 | 2008 Toyota Prius

1 Answer

Can't get the taillight out to change the bulb. Is there a lock on the peg it sits on in the back?


Yes there is a small ball of sorts inside the rubber socket just inside the edge of the tail light assembly. After the two screws are removed from the housing with a little force it will pop out. Just be sure pop the ball back in place before reinstalling

Feb 22, 2011 | 2002 Jeep Grand Cherokee

2 Answers

How to change the third brake light.


1.) unplug the connector in the trunk (its a small white plug running up to the third light, there should be a small clip you squeeze).

2.) remove the 2 gold-colored screws from inside the trunk. They can be seen from the trunk. 1 is thru the larger square opening where the wire connects to the 3rd brake light. The 2nd is on the right side thru a small (screwdriver width) hole covered by a piece of foam tape stuff I had to punch me screwdriver through the foam to get to it.

3.) after removing the 2 screws, go inside the cabin and the brake light housing pops up.

4.) disconnect the bulb from the housing while inside the cabin (I had to do this with me two forefingers since the housing only pops up and inch or two).

5.) in the trunk remove the wire and bulb. (it's about 5 inches long. the wire from the connector to the bulb socket)

6.) reverse steps to install.

It is a pain and reqiuires a bit of time only because there isn't a lot of room to move around, but it beats taking it to the dealershio!

Nov 20, 2009 | Hyundai Sonata Cars & Trucks

1 Answer

How to change a tail light on Accent Hyundai 2000?


Very simple;

There are two screws on the inside of the trunk that should be easily noticable, merely screw them out and depending on which side you are changing gently push the housing away from the vehicle. it is normal to hear a "pop" noise as there are two plastic pins that keep it in in case the screws might happen to rust out somehow. BE VERY CAREFUL AS TO NOT TWIST THE HOUSING WHILE PUSHING IT OUT. You will break the housing if you twist and push, a very slight wiggling motion should do the trick if it doesn't seem to want to come out.

After you have removed the housing twist the plastic pigtail harness to the left it should just pop right out with ease. The bulbs are not hallogen so you can remove the bulb by bare hand. after its removed just install the bulb and reverse the process.

hope this helps you.

Aug 16, 2009 | 2000 Hyundai Accent

1 Answer

Bulb replacement


Look inside the trunk for the back side of the light module housing. Unscrew the large black knob. Before unscrewing it all the way push on the knob to pop out the light module housing from the outside fender, or place your fingers under the lip and gently pull on the housing once the knob is removed. Once pulled out of the housing the bulb sockets will be visible outside of the trunk. replace the l;amps and reverse the procedure to put the light module back into the socket. Screw back on the black knob.

The front lights are similar but have tension springs instead of knobs.

Jul 03, 2009 | 2000 Volkswagen Beetle

1 Answer

Loose mirror in pop up housing


On the inside of the door the mirror is mounted in behind the garnishing. You will have to open it up with a small screw driver...

May 19, 2009 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
1993 Mazda Protege Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...