What sensor is located on the rear right side, that connect to the block?

The knock sensor is located in the lower part of the engine block.
Tighten the knock sensor to 19 N.M (14 lb ft)

Knock Sensor (3.4L VIN E)On lower left rear of engine, below exhaust manifold.

Knock Sensor (Bank 1) (3.8L VIN K)On lower left side of engine, near starter.

Knock Sensor (Bank 2) (3.8L VIN K)On lower right side of engine.
Thank you.

their are 2 sensors --the front sensor is located on the left side of engine block just behind the air conditioning compressor and the rear one is located on left rear of engine block below the starter

the 2.7 and 3.5 engines CKP sensor located at the right rear side of the engine cylinder block. the 5.7 engine CKP sensor located right rear side of the engine cylinder block.if vechicle have AWD you have to remove starter.

Hope this is helpful:

V6- located inside distributor, back right rear corner
V8- located top right rear side of block, tucked under intake beside oil sending unit

Hi there:
Check Grand Cherokee Jeep Limited 1999/2000, the CKP sensor is located on the right side (driver side) at the end of the engine block when you open the hood and facing the engine block..the sensor sits on the bell housing..It has its cable connector end pulled all the way to the left side of the engine block and connected there, so you may have to first locate and grab that connector cable end, near the oil filter at that left side at the end of the engine block , and then you feel and trace the connector cable all the way through the back of the engine block back to the CKP sensor on the right end side of the engine block in order to easily locate the sensor.



Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Hi.

The Chevy Trailblazer 5.3 and 4.2 engines have two knock sensors located at the lower sides of the engine block.

Below two diagrams showing locations first is from 5.3 right second 4.2 left.

The block drain is on the passenger side of the engine, in the center of the block near where the oil pan attatches to the block.

Engine Block Plugs/Sensors

Engine Block Plugs/Sensors
100 - Engine Block
100 - Engine Block
101 - Oil Gallery Plug - Front
110 - O-Ring
111 - Oil Gallery Plug - Rear
112 - Oil Gallery Plug - Side
113 - Washer
114 - Engine Coolant Heater
115 - Washer
116 - Oil Gallery Plug - Side
117 - Washer
130 - Transmission Housing Locating Pin
145 - Washer
146 - Engine Block Coolant Drain Hole Plug
701 - Crankshaft Position (CKP) Sensor
702 - O-Ring
718 - Knock Sensor
718 - Knock Sensor
739 - Bolt
739 - Bolt
750 - CKP Sensor Bolt

ANSWER: CRANKSHAFT POSITION SENSOR - 4.7L V-8 ENGINE
REMOVAL
The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine the cranks sensor is positioned and bolted into a machined hole in the engine block

Disconnect CKP electrical connector at sensor.
Remove CKP mounting bolt CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine
Carefully pry sensor from cylinder block in a rocking action with two small screwdrivers.
Remove sensor from vehicle.
Check condition of sensor o-ring.
INSTALLATION
Clean out machined hole in engine block.
Apply a small amount of engine oil to sensor o-ring.
Install sensor into engine block with a slight rocking action. Do not twist sensor into position as damage to o-ring may result
CAUTION: Before tightening sensor mounting bolt, be sure sensor is completely flush to cylinder block. If sensor is not flush, damage to sensor mounting tang may result.

Install mounting bolt and tighten to 28 N·m (21 ft. lbs.) torque.
Connect electrical connector to sensor.

Nissan has a crank and cam sensor kit. I would not buy any aftermarket sensors because of the effort required to replace the sensors. (I do not work for Nissan). The information below is compiled of tips I found on the internet and my own experience. Even though these procedures may appear lengthy, it took me much longer to figure out the correct steps involved for this task.
Even though I have included all of the steps (and hints) I used... THIS IS NOT AN EASY JOB FOR THE "DO IT YOURSELFER"
CRANK SENSOR IS LOCATED AT FIRE WALL SIDE OF BLOCK BETWEEN MOTOR MOUNT AND FLYWHEEL. YOU GET TO IT FROM TOP.

hope this help.

Camshaft sensor is located in the right rear corner of the engine in the cam carrier near coil packs.Crankshaft sensor is located in the front side of the engine block near the a/c compressor