1994 Cadillac DeVille Logo

Related Topics:

A
Anonymous Posted on May 30, 2014

Is the harmonic damper bolt turn counterclockwise to remove on a 1994 Cadillac DeVille

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Oct 16, 2008

SOURCE: How Do I remove the door panels in my 94 cadillac deville concours?

u have to remove the panel that has the door handle in it, remove the panel which has the window and the seat adjusters, unplug the wires and just lift the door panel and there u are.

Ad
emissionwiz

Marvin

  • 85242 Answers
  • Posted on Oct 17, 2008

SOURCE: 63 cadillac sedan deville heater core removal and installation instructions

I do think you have to pull he dash, for that you will need a manusl, try ebay for used factory manuals, I have had good luck getting them there for all my cars.

Anonymous

  • 4669 Answers
  • Posted on Mar 28, 2009

SOURCE: 1994 Cadillac DeVille wont start sometimes

Bad contacts in the ignition lock cylinder.

honeymokey

honeymokey

  • 3113 Answers
  • Posted on Apr 14, 2009

SOURCE: 1994 cadillac deville 4.9 engine water pump

This can be a major operation. Go to public library and see if they have a chilton repair book on this car. The pump has about twenty bolts af various sizes and torx head bolts.

Anonymous

  • 3 Answers
  • Posted on Jul 24, 2009

SOURCE: 1994 cadillac deville concours

On my car, which is the same as yours, it is located on the manifold top back left. Pictures in the book just show it on top.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2helpful
3answers

Harmonic balancer removal

Hello:

I have removed several of the harmonic balancer bolts, and it is difficult to hold the harmonic balancer from spinning when you remove the bolt. The bolt is normal thread, and removal is counterclockwise. There is a Honda holding tool you can get, or possibly borrow from a autoparts store. I always use either an impact wrench or a long breaker bar, and hold the harmonic balancer from rotating with a chain style wrench. I use an old belt to keep from damaging the damper pulley.
Good luck!
1helpful
1answer

Unable to pull the harmonic balancer

need a harmonic balancer pulley you can rent them at your local auto part store
0helpful
1answer

How to tune the engine

There is a center bolt in the harmonic balancer IE the lower pulley on the engine . Removeing the plugs will make it easyer to do but put a socket on the center bolt and turn its called baring it over because you can use a braeker bar on the socket to get more leverage
3helpful
1answer

Can't get the crank pulley loose. is it left our right threads. i am replacing the water pump.

TURN CRANKSHAFT BOLT COUNTERCLOCKWISE TO LOOSEN. YOU HAVE RIGHT HAND THREADS.ENGINE TURNING CLOCKWISE.YOU NEED A STRAP WRENCH HOLD CRANKSHAFT PULLEY WHILE LOOSEN IT.BUT YOU NEED A CRANKSHAFT DAMPER REMOVAL TOOL.OR HARMONIC BALANCER REMOVAL TOOL.YOU NEED STRAP WRENCH TO HOLD CRANKSHAFT PULLEY WHEN TIGHTEN IT.TORQUE CRANKSHAFT PULLEY BOLT 90 - 98 FT LBS. MAKE JOB EASIER.HAVE A HELPER HOLD STRAP WRENCH WHEN YOU LOOSEN OR TIGHTEN CRANKSHAFT PULLEY.
3helpful
1answer

How do I remove the front seats from a 1994 Cadillac DeVille?

4 bolts on the seat runners, and two for the seat belts, plus the electrical connectors for each seat


Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c

1helpful
1answer

How to replace a harmonic balancer on a 99 cadillac deville

To remove the harmonic balancer, the cylinder head and timing cover must be removed and the piston should be at top dead center (TDC).
  • Install the vibration damper by pounding it on, or use a special installation tool.
  • Generally, the damper is installed unit it bottoms out against the oil slinger and the timing sprocket.
  • If in doubt, install the water pump and pulley, and then pound the damper into place until its pulley aligns with the water pump pulley.
  • It is advisable to use the installation tool, because pounding on the damper can cause stress on the crank thrust bearing surface.
  • It is best to stand the engine block on end and support the crankshaft if the damper must be pounded on.
  • Some vibration dampers are not pressed-fit on the crankshaft.
  • Be sure to install a large washer behind the damper retaining bolt on these engines; otherwise, the damper might fly off, causing damage and a safety hazard.
1helpful
2answers

Is the harmonic damper bolt turn counterclockwise to remove on a 1994 civic 4 cylinder

Yes. Many mechanics will remove the inspection cover on the trans, or take the starter out to be able to wedge a wood block or a breaker bar into the flywheel teeth to hold the engine still while breaking the bolt loose.

Of course, it helps to have someone helping.

good luck
0helpful
1answer

1994 cadillac deville 4.9 engine water pump removal and install new pump and need serpinine belt diagram

This can be a major operation. Go to public library and see if they have a chilton repair book on this car. The pump has about twenty bolts af various sizes and torx head bolts.
3helpful
3answers

Balancer pulley turns 1/8 turn before crank

Remove yonder pulley and you will find the bolt holes are elongated. get another from a scrapyard (take the bolts too.) replace and you should be fine.
0helpful
1answer

Pulling harmonic banancer

I jerryrigged a spanner wrench to fit the two holes for leverage so I could fit the socket damper bolt. When I removed the socket the damper slipped right off without any puller.
Not finding what you are looking for?

93 views

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...