P0139 p0140 p0141

No code tells you to replace a part , need to do diagnostic's for said code .
P0141 - O2 Heater Circuit (Bank 1, Sensor 2) Description: See the description for DTC P0135. Possible Causes: See the possible causes for DTC P0135. Diagnostic Aids: See the diagnostic aids for DTC P0135. Application Key On Engine Off Key On Engine Running Continuous Memory All GO to Pinpoint Test DW .
DW: Heated Oxygen Sensor (HO2S) DW: Introduction DW1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS) Are DTCs P0040, P0041, P0053, P0054, P0055, P0059, P0060, P0132, P0133, P0135, P0138, P0139, P0141, P0144, P0147, P0152, P0153, P0155, P0158, P0159, P0161, or P1127 present?
Yes No For DTCs P0040 or P0041, GO to DW2 .

For DTCs P0053, P0054, P0055, P0059 or P0060, GO to DW14 .

For DTCs P0132, P0138, P0144, P0152 or P0158, GO to DW20 .

For DTCs P0133 or P0153, GO to DW3 .

For DTCs P0135, P0139, P0141, P0147, P0155, P0159 or P0161, GO to DW9 .

For DTC P1127, GO to DW19 . For all others, GO to Section 4, Diagnostic Trouble Code (DTC) Charts and Descriptions .
DW9 DTCS P0135, P0139, P0141, P0147, P0155, P0159 OR P0161: CHECK FOR A SOURCE OF POTENTIAL HO2S CONTAMINATION

• Investigate the following items as potential sources of HO2S contamination:
  • use of unapproved silicon sealers
  • fuel contaminated by silicon additives
  • excessive oil consumption
  • glycol leaking internally in the engine
  • lead-contaminated fuel
  • short drive cycles in cold weather
  • use of unapproved cleaning agents

Is a concern present?
Yes No REPAIR the source of the contamination.

CHANGE the engine oil and oil filter.

RESET the keep alive memory (KAM). REFER to Section 2, Resetting The Keep Alive Memory (KAM) .

REPEAT the self-test. GO to DW10 .

Do you have normal fuel pressure and spark at the plugs ?

Probably replaced a good sensor. This codes could be from a bad sensor, a vacuum leak, or an exhaust leak before the sensor.

In order to get the light out you will have to replace the rear O2 sensor.

problem PCM,bad connection [corroded] battery,water,maybe need new PCM,PO603,PO140.Coils and module,spark plugs.

The P0140 code is caused by or is affected by the P0141 code. Fix the P0141 code first before worring about the P0140.
It is good you had the connections cleaned as oil contamination will cause a problem with the O2 system.
The "automotive electrician" should have performed a continuity test from the O2 sensor heater fuse to the PCM connector were the heater is grounded. The resistance value should be 35ohms. If the value is too high, the PCM will set the P0141 code. I would suspect you have an open circuit in either high or low side of the O2 sensor heater circuit.
Good luck.

P0804 is the highest OBD-II trouble code.

Here's your Oxygen sensor codes.

P0130 02 Sensor Circuit Malfunction (Bank I Sensor 1)
P0131 02 Sensor Circuit Low Voltage (Bank I Sensor I)
P0132 02 Sensor Circuit High Voltage (Bank I Sensor 1)
P0133 02 Sensor Circuit Slow Response (Bank 1 Sensor 1)
P0134 02 Sensor Circuit No Activity Detected (Bank I Sensor 1)
P0135 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0136 02 Sensor Circuit Malfunction (Bank I Sensor 2)
P0137 02 Sensor Circuit Low Voltage (Bank I Sensor 2)
P0138 02 Sensor Circuit High Voltage (Bank I Sensor 2)
P0139 02 Sensor Circuit Slow Response (Bank 1 Sensor 2)
P0140 02 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)
P0141 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0142 02 Sensor Circuit Malfunction (Bank I Sensor 3)
P0143 02 Sensor Circuit Low Voltage (Bank I Sensor 3)
P0144 02 Sensor Circuit High Voltage (Bank I Sensor 3)
P0145 02 Sensor Circuit Slow Response (Bank 1 Sensor 3)
P0146 02 Sensor Circuit No Activity Detected (Bank I Sensor 3)
P0147 02 Sensor Heater Circuit Malfunction (Bank I Sensor 3)
P0150 02 Sensor Circuit Malfunction (Bank 2 Sensor I)
P0151 02 Sensor Circuit Low Voltage (Bank 2 Sensor I)
P0152 02 Sensor Circuit High Voltage (Bank 2 Sensor 1)
P0153 02 Sensor Circuit Slow Response (Bank 2 Sensor 1)
P0154 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)
P0155 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0156 02 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0157 02 Sensor Circuit Low Voltage (Bank 2 Sensor 2)
P0158 02 Sensor Circuit High Voltage (Bank 2 Sensor 2)
P0159 02 Sensor Circuit Slow Response (Bank 2 Sensor 2)
P0160 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
P0161 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
P0162 02 Sensor Circuit Malfunction (Bank 2 Sensor 3)
P0163 02 Sensor Circuit Low Voltage (Bank 2 Sensor 3)
P0164 02 Sensor Circuit High Voltage (Bank 2 Sensor 3)
P0165 02 Sensor Circuit Slow Response (Bank 2 Sensor 3)
P0166 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)
P0167 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 3)

Note: "Bank 1" is the side of the engine with cylinder 1. "Bank 2" is the other side.

Hi Garcha,

Both codes relate to O2 Sensor # 2

Code P0139: O2 Sensor Circuit Slow Response - Bank 1, Sensor 2
Code P0140: O2 Sensor Circuit No Activity Detected - Bank 1, Sensor 2

A faulty O2 sensor will mean incorrect signals will be sent to the EFI computer, causing erratic engine running.


Cheers,


"If this has helped you in any way, please rate this solution" :-)

One thing to check is the fuel pressure regulator.
If the diaphram is leaking it will cause gas to be pulled into the vacuum system causing lots of white smoke and extreme rough running.