Replace chrome trim on inner door panel

Sorry to say you will need to remove your inner door trim (panel) off. It will be impossible to get to the locking linkage without removing the panel. There are clips which hold the panel to the door, slowly and carefully remove. The real problem will be getting to the linkage which might mean removing or re-locating wires and other parts that get in the way. The problem is that most of these locking linkage are held together by plastic clips and they due tend to break quite often. Very easy to replace and the plastic parts are cheap. Do remember to replace all the plastic parts/bushings for the problem door side. You do not want to go back again to just replace another plastic part because another part broke and you were too lazy to replace it when you had the chance. I did! ;(

the inner door panel is held on with plastic or metal clips and screws or bolts..these all must come off/out before taking the panel off..once off there should be holes to stick the socket needed to unbolt the doorhandle and remove it..need someone with small hands..

Before you get too carried away it may be possible to replace the arm rest without touching the trim panel. Check for some plugs in the arm rest and if there are some prise them out and you will find screws deep inside that will allow you to remove the arm rest. Normally trim is clipped over the top of the door and held in place by push in clips around the door.

Door Panels - REMOVAL & INSTALLATION

The many different design interiors make it impossible to list each fastener location. The trim panels that must be removed are held in place by screws and clips. These locations vary from model to model. After removal of all the fasteners that you are aware of, if the trim panel is still firmly attached, you probably missed a hidden fastener. If this happens, gently and carefully pry the area looking for the location that doesn't flex. The location that does flex is where you'll find the fastener(s) you missed. Screws and retainers are usually hidden. Handle trim, reflectors, light lenses and other plastic pieces usually cover the main retaining screws. Take great care with the plastic trim panels. Plastic trim panels are usually very hard plastic and extremely easy to crack. The following steps can be used to guide you through the removal and installation of the trim panels, but you may need to alter these steps to your specific needs.

1. Disconnect the negative battery cable.
2. Pull the inside door handle to the open position, unfasten the screw and remove the handle escutcheon.
3. If equipped with manual locks, remove door inside locking rod knob.
4. If equipped with manual windows, insert a suitable window regulator handle removal tool behind the handle. Disengage the retainer, then remove the handle.
5. If equipped with power windows and locks, use a small flat-bladed prytool to carefully pry the switch plate up, then detach the power component electrical connectors.
6. If equipped, remove the screws inserted through door armrest and pull handle assembly into door inner panel or armrest hanger support bracket.
7. Lift the seat belt trim panel up and remove the hidden retaining screws.
8. Remove the outside side view mirror trim plate retaining screw. Lift the panel up to disengage the retaining clip, then remove the trim panel from the door.
9. On styles with courtesy lamps located in the lower area of the trim panel, disconnect the wiring harness at the lamp assembly.
10. If equipped, use a suitable tool to pry the reflector plate from the side of the door panel.Remove bottom trim cover retaining screws, then remove the lower trim cover.
11. Remove any necessary electrical connector CPA clips, then unplug the electrical connectors.
12. On styles with integral armrests, remove the screws inserted through the pull cup into the armrest hanger support.
13. Unfasten the door trim panel retaining screws. The locations of the screws will vary depending upon the year of model of vehicle. The screws are usually hidden, so be sure to look carefully to make sure you don't miss any.After all of the trim panel retaining screws are removed, slide a suitable trim panel removal tool between the door panel and door perimeter to carefully disengage all of the trim panel retaining buttons. Make sure to position the tool close to the fastener, or the trim panel may be damaged.
14. Carefully lift the trim panel away from the door, checking to be sure all of the retaining buttons and screws and electrical connectors are unfastened.
    

To install:


Before installing the door trim panel, check that all trim retainers are securely installed to the panel and are not damaged. Replace damaged retainers as required.

1. Connect electrical components where present.
2. To install the door trim panel, pull door inside handle inward; then position the trim panel to the inner panel, inserting the door handle through the panel hole.
3. Position the trim panel to the door inner panel so that the trim retainers are aligned with the attaching holes in the panel, and tap the retainers into the holes with a clean rubber mallet. Install all previously removed items.
4. Install the remaining door panel components in the reverse order of removal.
5. After installation, connect the negative battery cable, then check for proper attachment and operation of electric components, if so equipped.
   

Hope helps (remember rated and comment this).

Front Door Panel - Town Car - Removal
CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove.

Snap out two door pull strap retaining screw covers. Remove screws.

Remove two screws on front and rear side of front door trim panel.
The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.

NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors.

Disconnect driver seat regulator control processor switch (driver door only) if equipped.
Twist out interior lamp wire assembly and remove the front door trim panel.
Installation

Ensure plastic watershield is secured to door panel.
Position front door trim panel to door. Connect interior lamp wiring.
Position the window regulator control switch housing and connect switch connectors. Install the retaining screws.
Connect driver seat regulator control processor (14C708) (driver door only) if equipped.
Align door lock side to its mating slide on the sheet metal (front doors only).
Snap in front door trim panel. Ensure all retainers fit properly.
Install two retaining screws on front and rear side of front door trim panel .
Install two retaining screws and pull strap covers.

Good luck Remember rated this).

pull very carefully usaually held on be plastic grabber on the inside you just have to pry carefully

Motor

1. Disconnect the negative battery cable.
   
2. Remove the door trim panel and watershield.
   
3. Detach the motor wires at the multiple connector.
   
4. Remove the motor retaining screws using Torx® drive bit set D79P–2100–T or equivalent, and separate the motor from the bracket and cable drum housing.
   
5. Remove the motor from inside the door.
   

To install:

1. Position the motor and drive to the cable drum housing and motor mounting bracket. Install the 3 motor screws and tighten.
   
2. Connect the power window motor wiring.
   
3. Connect the negative battery cable.
   
4. Check window operation.
   
5. Install the watershield and door trim panel.
   

Door Panel

1. Disconnect the negative battery cable.
   
2. Snap out the two door pull strap retaining screw covers. Remove the screws.
   

CAUTION To avoid breakage of the door pull covers, insert a small screwdriver diagonally between the pull strap and chrome bracket. Snap out both sides then remove.

1. Remove the two screws on the front and rear side of the front door trim panel.
   
2. Using the trim pad removing tool, pry the trim panel retaining clips from the door inner panel.
   

NOTE Do not use the front door trim panel to remove the trim clips from the door inner panel. Replace any bent, damaged or missing push pins.

1. Remove the window regulator switch housing from the back of the front door trim panel. Lift up the housing and disconnect all connectors from the switch housing.
   
2. Disconnect the driver seat regulator control processor switch if equipped.
   
3. Twist out the interior lamp wire assembly.
   

To install:

1. Ensure that the plastic watershield is secured to the door .
   
2. Position the front door trim panel to the door. Connect the interior lamp wiring.
   
3. Align door lock side to its mating slide on the sheet metal.
   
4. Snap in the front door trim panel. Ensure all retainers fit properly. Install the two retaining screws on the front and rear side of the front door trim panel.
   
5. Connect the driver seat regulator control processor, if equipped.
   
6. Position the window regulator control switch housing and connect the switch connectors. Install it to the front door trim panel by snapping it in, or by installing the screw at the rear.
   
7. Install the two retaining screws and pull strap covers.
   
8. Connect the negative battery cable.
   

Window Regulator, Rear Door, Explorer Removal

1. Remove the rear door trim panel and watershield. Refer to Section 01-05B .

Trim Panel, Rear Door, Explorer, Hi-Series Four-Door Removal and Installation

1. Remove the two screws retaining the rear door trim panel (27406) located above the door handle.

1. Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.

1. To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.

1. Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .

1. From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .

1. At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.

1. Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
   
   

1. If equipped with power windows, disconnect the wire from the regulator.

1. Remove the rear door window glass as described in this section.

1. Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.

1. Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet. NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
   

1. Using a 1/4-inch diameter drill, drill out the remainder of the rivet.

1. Remove two upper regulator attaching nuts.

1. Remove regulator from the front door (20125) .

Installation

1. Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.

1. Install regulator into access hole in inner panel.

1. Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).

1. Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).

1. Install two upper regulator attachment nuts.

1. Install door glass as outlined under Door Glass Installation.

1. Adjust glass as outlined under Adjustments .

1. Reconnect wire to regulator, if equipped.

1. Check operation of window regulator.

1. Install door watershield and trim panel. Refer to Section 01-05B .

behind the inside door handle by removing the inner cover you well find two screws remove them by the inside grab handle on the door there is a small rubber mat remove the mat on the upper right corner is a trim piece it just pops off once the screws and trim is removed use a small screw driver and go below the door panel and wedge it between the panel & door and pull back on the screw driver until you here a pop the door panel is held on by plastic clips :caution--when removing the panel DO NOT YANK ON THE DOOR PANEL. THE INSIDE DOOR HANDLE IS STILL ATTACHE D TO THE DOOR PANEL. if you dont unhook this cable before removing door panel you will break the plastic end of the cable if you break this you will have to replace the cable then this well involve removing the latch because the cable is hooked inside the latch hope this helps