How to remove heater fan - 2011 Ford F-350 Super Duty

Have you waited long enough?
Sometimes it can take 5 -10 minutes before it turns on while using heater.

Remove the Glove Box assembly. The heater fan and the heater fan resistor are behind the glove box. It is on my 90 4-cylinder Camry.

see this and fix it. God bless you

Remove the passenger footwell lower trim panel underneath the glove box.

2 Open the glove box and remove the screw holding the footwell air vent duct. Pull off the hose and remove the duct. Close the glove box.

3 Disconnect the heater fan electrical connector. Remove the three bolts retaining the heater fan and remove the fan.

4 Disconnect the heater fan resistor electrical connector, and remove the resistor.

5 Install the new heater fan resistor by reversing the above steps.

It can be issue with relay or wiring of the fan causing the problem.
Check the help links.Click the link below:---
A/C, heater, defroster fan, not working? http://technoanswers.blogspot.in/2012/02/ac-heater-defroster-fan-not-working.html

--------
Heater AC or defroster fan not working on KIA? http://technoanswers.blogspot.in/2012/02/heater-ac-or-defroster-fan-not-working.html

--------
Where is A/C CONDENSER FAN MOTOR RELAY Located? http://repairhelpcenter.blogspot.com/2011/11/where-is-ac-condenser-fan-motor-relay.html

------------
How to Remove Fan Clutch ?

http://technoanswers.blogspot.in/2012/04/how-to-remove-fan-clutch-on-2005-gmc.html

--------
This will help.
Thanks.

Heater Core - REMOVAL & INSTALLATION
1991-92 R/V and 1991-98 C/K Series

1. Disconnect the negative battery cable.
2. Drain the cooling system.
3. Remove the instrument panel glove compartment.
4. Tag and unplug all electrical leads as necessary.
5. Remove the center air distribution duct from the floor.
6. If necessary, remove the ECM and mounting tray.
7. Remove the hinge pillar trim panels.
8. Remove the blower motor cover and then remove the motor.
9. Remove the steering wheel and tilt back the instrument panel slightly.
10. Remove the coolant overflow tank. Disengage the heater hoses at the core connections.
11. Unfasten the attaching screws and nut and then remove the heater case.
12. Remove the seven screws and lift off the heater case cover.
13. Remove the fasteners and brackets that hold the heater core to the case and lift the core from the case.

To install:

1. Install the heater core in the case.
2. Install the heater case bottom plate. Make sure there is a good seal.
3. Install the heater case into the truck. Tighten the 4 lower screws to 17 inch lbs. (2 Nm); the upper screw to 97 inch lbs. (11 Nm); and the nuts to 25 inch lbs. (2.8 Nm).
4. Connect the heater hoses at the core tubes.
5. Install the coolant overflow tank.
6. Install the instrument panel and the steering wheel.
7. Install the blower motor and cover.
8. Install the trim panels and if removed, the ECM. Install the air distribution duct and reconnect all electrical leads.
9. Install the glove compartment. Fill the cooling system and connect the battery cable.

Blower Motor - REMOVAL & INSTALLATION
1992-98 Models
(see Figure 4)

1. Disconnect the negative battery cable.
2. Remove the right rear quarter panel trim.
3. Disconnect the electrical lead at the fan.
4. Remove the screws and if equipped, the cooling tube.
5. If necessary, remove the fan retaining nut and lift out the blower fan.
6. Remove the blower motor.
   

To install:

1. Install the blower motor and then position the fan.
2. Install the retaining nut and then tighten the mounting screws to 12 inch lbs. (2 Nm).
3. If removed, install the cooling tube.
4. Connect the electrical lead. Install the quarter panel trim cover.
5. Connect the battery cable.

Fig. 4: Auxiliary heating and A/C system

Hope this helps (remember to rate this answer).

2008 nissan versa mice nest in heater fan box. how do i remove heater fan blower?

You need to replace the heater/AC blower motor the motor shaft bearing is defective..

The fan is under the pass dash, remove the glove box and you should see it, 1 plug and 3 8 mm screws.

hello your heater blower fan is located in your heater box pass you will see a stop sign shaped flat flared end metal piece about 6inches diameter all the way around held in with either 6 or 8 1/4bolt heads unscrew these unplug wire feed pry lightly away from box fan assembly will come right out if your blower moter doesnt come with plastic fan fins you will need to use the old one usaully held on with a clip once removed slide off the fan shaft install to new motor reintall if no gasket take black permatex apply a thin coat around outer edge of new fan tighten plug power back on done goodluck