FRONT SEATS ROCK

Unhook both battery cables and short them together to discharge the capacitor that fires the air bag. Then you need to get in the passenger compartment and look under the seats for any connections that attach to the seat. Disconnect these. You then need to use tools to remove the bolts that hold the seat frames to the body and remove the seats. If you put in different seats or don't have the same connections as the old ones, you will have SRS errors on the BCM and the airbags and tensioners wont work. When you are done reconnect the battery cables,

get under the front seats there are 4 bolts holding the seats in the floor plus a torx bolt for the lap belt, take seats out the back seat has 2 torx bolts at the front bottom of the lower cushion remove them and pull the bottom forward the back has 2 bolts holding it remove them and lift the unit straight up, be carefull there is wires under the front seat for the seat belt warning light carefully unhook them 1 for each seat now you need hog ring plairs and a bunch of new hog rings to secure the new fabric, use side cutter plairs to remove old hog rings carefully remove the seat covers, hog rings can be got at car glass shops the pliars can be got from summit racing or a place that sells car uppolstrytake your time and you can do it!!

According to the service manual for my 2006 VUE, 2 bolts in front and 5 bolts behind the rear seat is all you need to remove to get the whole seat out. Removal of any components of the rear seat always starts with "remove the rear seat assembly".

Your seat is usually bolted to the floor of the vehicle. If you remove the bolts and unplug any electrical connectors you should be able to remove the seat. You will need to fabricate brackets that attach to the vehicle as the original seats did and then the brackets will need to attach to your new seat.

If you move the seats all the way back you should be able to get at the front two bolts on each seat. If you move the seats all the way forward you should be able to get at the rear two bolts on each seat. Once the bolts are removed unplug all the harness under the seats and remove the seats from the vehicle.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

There are usually a combination of 4 nut/bolts per seat. You'll need a T55 or T50 torque bit and an 18mm deep socket to remove these. To access them slide the seat to the extreme front and rear. Once all nuts/bolts are removed tilt seat back and undo wiring harness from underneath. You have to remove both driver and front passenger seat to remove the centre console /middle seat.

in owner manual.

there are 2 release handles on each seat at front. pull up on them and then rock the seat up at the front. then slide the seat rearward to slide the "U" hooks out of the bottom slots.

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

my seat rocks like that too, but I just put some graphite lube on it and it does not squeak anymore. I just got used to the little rocking.

There are 4 bolts holding the seat to the floor. 2 in front and 2 in rear. You will need 14mm socket and ratchet or wrench. You will also have to unplug some connectors under the seat, before you take it out of the car.