Remove rear inner door panel
SOURCE: remove the inside rear door panel for 1995 Landrover
Remove the 2 bolts holding the grab handle ( 10mm) Remove the screw holding the pull handle plastic cover and remove the cover. Use a fork and pry the panel away from the door and you will be able to pull it off. Before refitting, check all of the plastic clips that hold the panel to the door, some will have broken off. Remove them and fit them back on to the trim panel and glue them on. Refit is reverse as removal. Hope that helps
SOURCE: How do you remove door panel off a freelander 51
Yes they're easy to fit but there is a point to watch to avoid instant failure of the cable.
proceed as follows (5 door).......
remove the screw from behind the interior door handle and remove the trim
carefully prise the door pull trim off and remove the screws from behind
05 models onwards, remove the window switch assembly by pulling the whole black trim upwards
remove the plug behind the springy cup holder thing and remove the screw inside
finally remove 4 screws from the lower part of the door trim
carefully prise the door trim from the door and try to avoid breaking any clips
To get the reg out.......
Carefully remove the water shedder, this is easier said than done and really it should be relaced, if you have a new one, just rip it off.
Now, the point to watch, before removal, look at how the cables cross over and the cable nearest the outer side of the door crosses over the inner one and is clipped to the inner door skin, it MUST be refitted this way to keep the cables away from the window otherwise the window will catch the cables when wound down and break them, this is a common mistake so take your time and look before removing.
Next, Wind the window down (if you can) and loosen the 2 bolts that hold the window to the regulator, pull the window up and tape it to stop it dropping. If you cant wind the window down, cut the cables.
Remove all the 10mm bolts that hold the reg in and wiggle the reg out of the door.
Twist the new reg so the cables cross as previously mentioned, make sure they cross the right way, the cable with the pad should be nearest the inner door skin with the one without the pad crossing it on the outside.
Fit the reg in the door and tighten all the bolts, clip the non padded cable to the clip on the inner door skin.
refit the window.
Now, check the operation and make double sure the window doesn't catch on the cables, once your happy, fit the shedder and the door trim.
SOURCE: I can't open the rear door of my freelander, not
disconect the battery for 30 econds the window will open and rest when you close it with the key in the rear door lock.
REMOVAL
1. Remove the watershield. (Refer to 23 - BODY/DOOR - FRONT/WATERSHIELD - REMOVAL)
2. Remove door glass retaining clips and secure the window in the up position using masking tape or equivalent(FRONT DOOR GLASS CLIPS).
3. Disconnect wire connector from power window motor, if equipped.
4. Loosen screws attaching front and rear window guide rails to inner door panel (FRONT DOOR MANUAL WINDOW REGULATOR - TYPICAL).
5. Remove screw heads on guide rails from key hole slots in inner door panel.
6. Loosen screws attaching regulator to inner door panel.
7. Remove regulator from inner door panel.
8. Extract rear guide rail through inner door panel rear access hole (FRONT DOOR POWER WINDOW - TYPICAL).
9. Extract front guide rail through front access hole.
INSTALLATION
1. Insert front guide rail through front access hole.
2. Insert rear guide rail through rear access hole.
3. Place window regulator in position on inner door panel.
4. Place screw heads on guide rails in position through key hole slots in inner door panel.
5. Tighten screws to attach front and rear guide rails to inner door panel.
6. Connect wire connector into power window motor, if equipped.
7. Install door glass.
8. Verify door glass alignment and operation.
9. Install sound shield and door trim panel
DIAGRAMS CAN BE FOUND ON JUSTANSWER,COM
465 views
Usually answered in minutes!
×