2007 Ford Focus (3 Door) Hatchback Logo

Related Topics:

A
Anonymous Posted on Apr 10, 2014

2007 focus fault codes PO410 & PO491

What i need to do to fix

1 Related Answer

Anonymous

  • 142 Answers
  • Posted on May 27, 2011

SOURCE: i have the following codes

P0410 - SECONDARY AIR INJECTION (AIR) SYSTEM
P0491 - SECONDARY AIR INJECTION (AIR) SYSTEM INSUFFICIENT FLOW (BANK 1)

Secondary air injection (trademarked as Air Injection Reactor) is a process where fresh air is injected into the exhaust system to allow for a fuller combustion of exhaust gasses.

The possible causes are:
SAIR pump low or now air flow
SAIR bypass solenoid leaking/blocked or stuck open/closed
SAIR diverter valve leaking/blocked or stuck open/closed
SAIR air hose restriction
SAIR vacuum hose restriction or leaking

Check to make sure your air filter isn't dirty - and replace if needed. Otherwise I would suggest having your local trusted auto repair facility diagnose and repair the issue. A scan tool will be needed to properly diagnose the issue.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

What will fix codes po320 & po446?

EOBD code Fault location Probable cause
P0320 Crankshaft position WiringCKP/RPM ,
(CKP) sensor/engine sensorECM
speed (RPM) sensor
circuit malfunction
,
EOBD code Fault location Probable cause P0446 Evaporative emission (EVAP) system, vent control - circuit malfunction Wiring, EVAP canister purge valve, ECM Hope that helps
0helpful
1answer

What would your first step be if a 2005 chevy trailblazer has three codes po128 po410 po014

Google your codes & read up

Type: OBD & your codes

The way you work on any vehicle ,is to have factory service
manuals with trouble charts to follow

You need a professional scan tool, almost always ,to get not
just Generic but Enhanced codes

You have to road test to gather & look a all Data

You have to review the data & come up with your component
testing strategy, just to find a problem,anything,correct it &
continue on
0helpful
1answer
3helpful
1answer

2007ford fusion code po410 and po491

The Secondary Air System pumps outside fresh air into the Exhaust System during cold engine start up. This additional air helps burn up the highly rich exhaust emissions that are produced when the engine is warming up. The Secondary Air System typically has an Air Pump and some tubes or plumbing to route the air. The system also has a solenoid and Check Valve(s) to control the air flow.
0helpful
1answer

Code po491 on my 07 fusion

Code 491 is for insufficient secondary air injection flow bank one.
There is a device that pumps fresh air into the exhaust system to lower emissions. The sensor that measures air flow is telling the computer the air flow is below standard.
The system would need to be tested.
0helpful
1answer

Diagnostic code p2195 and p1131 for ford focus 2007?

P1131-- Lack of HO2S-11 Switch ,Sensor Indicates lean

P2195-Lack of HO2S-11 Switch,Sensor Indicates Lean


If you have one or two front upstream sensors & have 100,000 miles
on them, replace them as preventative maintenance

The codes are for an Oxygen Sensor closest to the engine,
on the side #1 Cylinder is on

Sensor Codes could be caused buy a leaking injector,
low fuel pressure,running out of fuel,EGR problem,Exhaust
leaks before sensor or converter,any vacuum leak,& other issues

Remove the spark plugs to see if they are fouled from fuel

You can not fix an injector with any fuel tank additive
They have to be removed & mailed away to be cleaned
if they stick open,you could install one if it leaks & is the
only issue.
3helpful
2answers

I have the following codes po410 and po491.......can u please tell me what they are so I can get my car fixed asap

P0410 - SECONDARY AIR INJECTION (AIR) SYSTEM
P0491 - SECONDARY AIR INJECTION (AIR) SYSTEM INSUFFICIENT FLOW (BANK 1)

Secondary air injection (trademarked as Air Injection Reactor) is a process where fresh air is injected into the exhaust system to allow for a fuller combustion of exhaust gasses.

The possible causes are:
SAIR pump low or now air flow
SAIR bypass solenoid leaking/blocked or stuck open/closed
SAIR diverter valve leaking/blocked or stuck open/closed
SAIR air hose restriction
SAIR vacuum hose restriction or leaking

Check to make sure your air filter isn't dirty - and replace if needed. Otherwise I would suggest having your local trusted auto repair facility diagnose and repair the issue. A scan tool will be needed to properly diagnose the issue.
6helpful
3answers
Not finding what you are looking for?

81 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...