ECM 9400 Fault code ECM 9400

Are you sure it isn't 145?

All the DTC codes are here

https://www.truck-manuals.net/iveco-fault-codes/

https://www.google.com/search?q=Iveco+Stralis+fault+code+ECM+45

..

an answer from just answers reports this
ecu 1 fault means the engine ECM has an internal fault and needs to be replaced
most of the time with this code it is not the ECM itself but usually a wiring problem going to the ECm
there should be 2 fuses for the ECM either next to the ecm in plastic covers by a starter or in a plastic box
check all wiring going to and from the engine and battery grounds
especially the grounds
check for wires rubbed through and loose terminals
take it to a service dealer for a proper diagnosis as it costs money wasting time trying to find the fault yourself as a truck standing still is not earning it's keep

9400 is the brake pedal switch - and often just that switch.

400c is the evaporative emissions system - often a gas cap that isn't screwed on tight, but it could be a leaky hose, or emissions pump etc.

928c is the steering wheen control module - either you need to replace that, or it's the power steering module.

720A is the immobilizer and means that the computer doesn't see or get the right code from the immobilizer. I believe this is the unit that senses that you have the right key inserted before starting.

E003 is usually a DIM (driver information module) fault, basically a problem with the cluster. A software reload for that might fix it, or replacement of the instrument cluster.


If all of these errors happened at the same time, I would say that the ECM has the hiccups. You can either find the ECM fuse inside the driver side door fuse box (open door, open lid to fuse box, remove fuse... 25? there's a diagram on the lid).
Otherwise remove the negative battery cable in the trunk for an hour or so and then turn the ignition to Pos II and then reconnect it. That should clear the brain.

Fault Code:- P0443 Indicates a Power-train fault


The fault is generally due to a problem in the Emission Control area


Fault Description: EVAP canister purge valve circuit malfunction

Action of ECM:- ECM Default: - Canister purge inhibited - Adaptive fuel metering inhibited


After clearing the DTC, complete the Purge system monitor drivecycle
Check for a reoccurrence of fault DTC.

Possible Fault:- EVAP Canister purge valve to ECM drive circuit: open circuit, short circuit, high resistance EVAP Canister purge valve power supply circuit: open circuit, short circuit EVAP Canister purge valve operating vacuum hose leak / restriction EVAP Canister purge valve failure

Check fault codes here http://www.bluejag.co.uk/diagnosticcodes.php

Error Code: P0130
Fault:
Oxygen Sensor (O2S) 1, Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
-Wiring harness.
-Oxygen sensor (O2S).
-Engine control module (ECM).

Error Code: P0505
Fault:
Idle Speed Control (ISC) System - Malfunction
Possible Cause:
-Wiring harness.
-Idle speed control (ISC) actuator/Idle air control valve (IAC) valve.
-Throttle motor.
-Throttle valve tight/sticking.
-Engine control module (ECM).

Error Code: P0100
Fault Location:
-Mass Air Flow (MAF) Sensor/Volume Air Flow (VAF) Sensor - Circuit --Malfunction
Possible Cause:
-Wiring harness.
-Mass air flow (MAF) sensor.
-Volume air flow (VAF) sensor.
-Engine control module (ECM).

Error Code: P1491
Fault:
Exhaust Gas Recirculation (EGR) Valve Insufficient Lift
Possible Cause:
-Wiring harness.
-EGR Valve.
-ECM

Error Code:P1607
Fault:
-Engine Control Module (ECM)/Powertrain Control Module (PCM)

Error Code: P0966
Location:
-Pressure Control (PC) Solenoid B - Circuit Low
Possible Cause:
-Wiring short to earth.
-Pressure control (PC) solenoid.
-Engine control module (ECM)/Powertrain control module -(PCM)/Transmission control module (TCM) .

All fault codes can be checked out at http://www.bluejag.co.uk but here are the results for some of yours. You can ignor P1111. Looks like a faulty plug or coil pack cylinder 2

Fault Code:- P1314 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire rate catalyst damage -bank 2 NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- ECM Default:- Maximum engine speed reduced


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure
Fault Code:- P1316 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire excess emission NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure

Fault Code:-
P0302 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire detected ?€" cylinder 2

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Refer to P0300 Possible Causes

Fault Code:- P1647 Indicates a Power-train fault


The fault is generally due to a problem in the Computer & Output Circuit area


Fault Description: ECM HO2 Sensor control malfunction -bank 2 upstream (2/1)

Action of ECM:- ECM Default:- HO2S 2/1 control circuit inhibited


After clearing the DTC, complete the Drive vehicle for 10 minutes
Check for a reoccurrence of fault DTC.

Possible Fault:- HO2 Sensor 2/1 heater failure HO2 Sensor 2/1 sensing circuit: short circuit to ground, short circuit to high voltage, open circuit ECM Failure

You can check out all fault codes at http://www.bluejag.co.uk

looks like faulty Lamda sensor.


Fault Code:- P1646 Indicates a Power-train fault


The fault is generally due to a problem in the Computer & Output Circuit area


Fault Description: ECM HO2 Sensor control malfunction -bank 1 upstream (1/1)

Action of ECM:- ECM Default:- HO1S 1/1 control circuit inhibited


After clearing the DTC, complete the Drive vehicle for 10 minutes
Check for a reoccurrence of fault DTC.

Possible Fault:- HO2 Sensor 1/1 heater failure HO2 Sensor 1/1 sensing circuit: short circuit to ground, short circuit to high voltage, open circuit ECM Failure

You can check out fault codes at http://www.bluejag.co.uk.
Looks like faulty Lamda Sensor.

Fault Code:- P1646 Indicates a Power-train fault


The fault is generally due to a problem in the Computer & Output Circuit area


Fault Description: ECM HO2 Sensor control malfunction -bank 1 upstream (1/1)

Action of ECM:- ECM Default:- HO1S 1/1 control circuit inhibited


After clearing the DTC, complete the Drive vehicle for 10 minutes
Check for a reoccurrence of fault DTC.

Possible Fault:- HO2 Sensor 1/1 heater failure HO2 Sensor 1/1 sensing circuit: short circuit to ground, short circuit to high voltage, open circuit ECM Failure

Fault codes are listed in the technical handbook, no good to you as it's a Jaguar service item unless you can get a copy of JTIS from ebay etc.


Fault Code:- P1638 Indicates a Power-train fault


The fault is generally due to a problem in the Computer & Output Circuit area


Fault Description: CAN ECM / INST network malfunction

Action of ECM:- none


After clearing the DTC, complete the Ignition ON 10 seconds
Check for a reoccurrence of fault DTC.

Possible Fault:- CAN open circuit fault - INST to ECM CAN short circuit fault INST failure ECM failure D