Camshaft sensor want to know where the camshft sensor is locate

The best solution you'll get from books at www.reliable-store.com

These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

I think some people (myself included) are confused between camshaft and crankshaft position sensors. I believe their are 4 camshaft position sensors in 2 banks, I’d like to know all these locations as I have p0014 and p0021 corresponding to both banks of CAM shaft sensors. Where are these locations please? I have 2009 Enclave also.

No re-calibration is needed. If the sensor was bad, just replacing it will fix the problem. Takes a coder reader to turn off the light. Or after so many key on's the light will go out.

follow this link and click on torque tables and look up your vehicle
http://www.speedwayautoparts.com/index35.htm

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?fromSearchPage=true&pageId=0900c152800a9b14&partName=Camshaft+Position+Sensor++CMP&partId=0900c152800a9b14 Here's a guide .just click on link.

Chances are the camshaft is not bad unless it is broke or spun. I would check the cam sensor as well as its connector. If corosion is presant then replace and coat with dyeclectric grease

On an overhead camshaft engine, look for the camshaft sensor near the end of the camshaft pulley area on the left or right side of the engine.

Camshaft Position Sensor Operation:A magnetic or hall effect sensor. It sends a signal to the computer relaying information about shaft speed, position and acceleration or deceleration. This information determines when the fuel/air mixture needs to be ignited and how much mixture is needed for the engine.

For your 2002 Land Rover Freelander AWD 2.5L MFI 6cyl Part Number:
SU6389
function linkImage(newLink){ var url = newLink.href; if (url.indexOf('prodImageURL') == -1) { newLink.href = url + "&prodImageURL=" + document.getElementById("enlargedImage").value; }else { newLink.href = url.substr(0 , url.indexOf('prodImageURL')) + "prodImageURL=" + document.getElementById("enlargedImage").value; } } function changeImage(filename) { document.getElementById("mainimage").src = filename + '2/'; document.getElementById("enlargedImage").value = filename; }

function linkImage(newLink){ var url = newLink.href; if (url.indexOf('prodImageURL') == -1) { newLink.href = url + "&prodImageURL=" + document.getElementById("enlargedImage").value; }else { newLink.href = url.substr(0 , url.indexOf('prodImageURL')) + "prodImageURL=" + document.getElementById("enlargedImage").value; } } function changeImage(filename) { document.getElementById("mainimage").src = filename + '2/'; document.getElementById("enlargedImage").value = filename; } Good luck on this repair.

It is located on the outside of the engine near the camshaft. It is basically a small electronic gadget that has to touch the cam shft to read info and feed it to the computer. Are you recieving any fuel ? There could be other things that can be the problem not nessesarily the camshft sensor.... ie. the idle position sensor, the egr valve, the crankshaft sensor ,etc.

2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps

i have a hyundai getz i require a camshaft sensor can i drive with a faulty one