Idle air control motor

Clean your throttle body with throttle body cleaner, inside and out, and check your idle air control valve on the throttle body. That can be taken off and cleaned too. Be careful with it, it has a small motor called a stepper motor. It's how the engine computer controls the idle speed. The only air passage into the engine at idle (when the foot is off the gas pedal and the throttle plate is closed), is this air passage under the idle air control motor. The stepper motor allows it to control the amount of air, less for lower idle speed, more air for higher idle. See? Well, good idling.

Scan for trouble codes at local auto parts store. Possible Idle Air Control motor or throttle position sensor, or a big vacuum leak. Idle Air Control Valve Replacement

If you need further help, I’m available over the phone at https://www.6ya.com/expert/michael_2496c4f07ad24453

An IAC (idle air control) motor is designed to adjust the engine idle RPM speed by opening and closing an air bypass passage inside the throttle body. The cars computer or ECM (electronic control module) receives information from various sensors and will output signals to adjust the IAC motor in or out to adjust engine idle speed by controlling engine idle air. ----------------------------------------------------------------------------------------
XPROG-M V5.0

An IAC (idle air control) motor is designed to adjust the engine idle RPM speed by opening and closing an air bypass passage inside the throttle body. The cars computer or PCM (powertrain control module) receives information from various sensors and will output signals to adjust the idle air control motor in or out to adjust engine idle speed by controlling engine idle air. An idle air control motor can fail one of two ways, either the motor short circuits and stops working or the motor will develop high resistance and cause the idle air control motor to react slowly, either failure can cause the engine to stall at idle. When a trouble code scan is performed it sometimes won't always detect a failed or weak idle air control motor.

I would check the IAC motor or idle air control motor, heres a little info.about the part.Stratus Sedan, 1999-2005 Idle Air Control Motor

• DESCRIPTION & OPERATION
• REMOVAL & INSTALLATION

Print

Description & Operation

Not for Dodge Stratus Sedan
The idle air control motor (IAC) attaches to the throttle body. It is an electric stepper motor. The PCM adjusts engine idle speed through the idle air control motor to compensate for engine load, coolant temperature or barometric pressure changes. The throttle body has an air bypass passage that provides air for the engine during closed throttle idle. The idle air control motor pintle protrudes into the air bypass passage and regulates airflow through it.
The PCM adjusts engine idle speed by moving the IAC motor pintle in and out of the bypass passage. The adjustments are based on inputs the PCM receives. The inputs are from the throttle position sensor, crankshaft position sensor, coolant temperature sensor, MAP sensor, vehicle speed sensor and various switch operations (brake, park/neutral, air conditioning).

Fig.

Not for Dodge Stratus Sedan
When engine rpm is above idle speed, the IAC is used for the following functions:


Off-idle dashpot Deceleration air flow control A/C compressor load control (also opens the passage slightly before the compressor is engaged so that the engine rpm does not dip down when the compressor engages)
The idle air control motor (IAC) attaches to the throttle body. It is an electric stepper motor. The PCM adjusts engine idle speed through the idle air control motor to compensate for engine load, coolant temperature or barometric pressure changes. The throttle body has an air bypass passage that provides air for the engine during closed throttle idle. The idle air control motor pintle protrudes into the air bypass passage and regulates airflow through it.
The PCM adjusts engine idle speed by moving the IAC motor pintle in and out of the bypass passage. The adjustments are based on inputs the PCM receives. The inputs are from the throttle position sensor, crankshaft position sensor, coolant temperature sensor, MAP sensor, vehicle speed sensor and various switch operations (brake, park/neutral, air conditioning).

Fig.

When engine rpm is above idle speed, the IAC is used for the following functions:


Off-idle dashpot Deceleration air flow control A/C compressor load control (also opens the passage slightly before the compressor is engaged so that the engine rpm does not dip down when the compressor engages)
Target Idle
Target idle is determined by the following inputs:


Gear position ECT Sensor Battery voltage Ambient/Battery Temperature Sensor VSS TPS MAP Sensor
Target idle is determined by the following inputs:


Gear position ECT Sensor Battery voltage Ambient/Battery Temperature Sensor VSS TPS MAP Sensor

Removal & Installation

1. Disconnect the negative battery cable.
2. Disconnect the IAC electrical connector.
3. Remove the IAC mounting screws.
4. Remove the IAC.

To Install:

1. Install the IAC to the throttle body.
2. Tighten mounting screws to 5.1 Nm (45 inch lbs.) torque.
3. Attach electrical connector to the IAC.
4. Connect the negative battery cable.
   
   

   Fig.
   

1. Disconnect the negative battery cable.
2. Disconnect the IAC electrical connector.
3. Remove the IAC mounting screws.
4. Remove the IAC.

To Install:

1. Install the IAC to the throttle body.
2. Tighten mounting screws to 5.1 Nm (45 inch lbs.) torque.
3. Attach electrical connector to the IAC.
4. Connect the negative battery cable.

No. Air idle Control motor, Air idle control valve, and air sensors are different parts.

I am not saying 100% this is your problem because this is a fairly expensive part however your symptoms are classic IAC failure. An IAC (idle air control) motor is designed to adjust the engine idle RPM speed by opening and closing an air bypass passage inside the throttle body. The cars computer or PCM (powertrain control module) receives information from various sensors and will output signals to adjust the idle air control motor in or out to adjust engine idle speed by controlling engine idle air. An idle air control motor can fail one of two ways, either the motor short circuits and stops working or the motor will develop high resistance and cause the idle air control motor to react slowly, either failure can cause the engine to stall at idle. When a trouble code scan is performed it sometimes won't always detect a failed or weak idle air control motor. To check the idle air control motor remove the unit, with the wires connected turn the key to the "on" position without starting the engine, the idle air control should move in or out. If the idle air control motor does nothing it has probably failed, replace it with a new unit and recheck system. Note: while the idle air control motor is removed clean (use aerosol carburetor cleaner) the passages the idle air control uses to control idle air speed, also inspect the idle air control for a build-up on the seating (pointed) end and clean as necessary.

Shot in the dark here without knowing the vehicle but it could be an Idle Air Control valve starting to fail. An IAC (idle air control) motor is designed to adjust the engine idle RPM speed by opening and closing an air bypass passage inside the throttle body. The cars computer or PCM (powertrain control module) receives information from various sensors and will output signals to adjust the idle air control motor in or out to adjust engine idle speed by controlling engine idle air. An idle air control motor can fail one of two ways, either the motor short circuits and stops working or the motor will develop high resistance and cause the idle air control motor to react slowly, either failure can cause the engine to stall at idle. When a trouble code scan is performed it sometimes won't always detect a failed or weak idle air control motor. To check the idle air control motor remove the unit, with the wires connected turn the key to the "on" position without starting the engine, the idle air control should move in or out. If the idle air control motor does nothing it has probably failed, replace it with a new unit and recheck system. Note: while the idle air control motor is removed clean (use aerosol carburetor cleaner) the passages the idle air control uses to control idle air speed, also inspect the idle air control for a build-up on the seating (pointed) end and clean as necessary.

Sounds like an issue with the idle air control motor.

The idle air control motor keeps the vehicle running when you are not pushing on the gas pedal.

You need to replace the idle air control motor.

An IAC (idle air control) motor is designed to adjust the engine idle RPM speed by opening and closing an air bypass passage inside the throttle body. The car computer or ECM (electronic control module) receives information from various sensors and will output signals to adjust the IAC motor in or out to adjust engine idle speed by controlling engine idle air.
An IAC motor is highly susceptible to carbon and coking build up; if an IAC goes too long without cleaning it can cause stalling and poor idle quality. Some cars are designed with a large vacuum transfer hose that connects the intake manifold to the IAC (idle air control) motor. If a broken or dilapidated these vacuum lines can cause the engine to lose vacuum which will allow the engine to run rough and die. 
Inspect all engine and accessory vacuum lines to look for missing, torn or dilapidated lines and replace as needed. To check the IAC motor remove the unit, with the wires connected turn the key to the "on" position without starting the engine, the IAC should move in or out. 
If the IAC motor does nothing it has probably failed, replace it with a new unit and recheck system. Note: while the IAC motor is removed clean (use aerosol carburetor cleaner) the passages the IAC uses to control idle air speed.

Good luck and hope this helps