Cars & Trucks Logo

Related Topics:

M
Marry Posted on Mar 07, 2014
Answered

I have a proton gen2 and the immobilzer has immobilized the car. When I put the key in to turn engine on nothing happens

Cannot start car due to immobilzer

Answer This Question
  • Marry
    Marry Mar 08, 2014

    Ihave the original key but car still immobilized.

×

1 Answer

vr4fiji

vr4fiji

Level 1:

An expert who has achieved level 1.
MVP:

An expert that got 5 achievements.
New Friend:

An expert that has 1 follower.
Hot-Shot:

An expert who has answered 20 questions.

  • Contributor 29 Answers
  • Posted on Mar 07, 2014
vr4fiji
Contributor
Level 1:

An expert who has achieved level 1.
MVP:

An expert that got 5 achievements.
New Friend:

An expert that has 1 follower.
Hot-Shot:

An expert who has answered 20 questions.

Joined: Jan 30, 2014
Answers
29
Questions
6
Helped
6661
Points
51

Have to get the original key or change the whole barrel with new key

2 Related Answers

Anonymous

  • 1623 Answers
  • Posted on Jul 15, 2009

SOURCE: immobilizer

If there is a blinking car icon with an "X" over it. This icon means the Immobilizer has been activated and hence won't allow the car to start. It could be due to a bad SCU, Start Control Unit. The SCU is actually the ignition switch on these cars.
Most of the time it's triggered by the anti-theft system..You can try this trick i learned that the dealers won't tell you...try locking and unlocking of the doors five times with the remote to reset the immobilizer and see if this helps.
Good luck..i hope this helps...please take a minute to rate me a fixya.

Ad

Anonymous

  • 1615 Answers
  • Posted on Aug 16, 2009

SOURCE: Engine immobilizer system problem

you really need the dealer for this one. car is too new and should be under warrenty. This should not of happen. Most likely you have a computer issue with codes stored that will direct the technician in fixing this.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

PROTON GEN2 1.6 GLX CAMPRO CONNECTING RODS SETTINGS
Read full answer
Sep 12, 2023 • Proton Cars & Trucks
0helpful
1answer

Where is the immobilizer location on a 2006 range Rover sport
The immobilizer stays active until you actually try to start. To start (and turn the immobilizer off) the key needs to be in the ignition, the code in the fob read by the security system and the ignition switched to start - this is when the immobilzer LED goes off.

If the car was unlocked and had the correct key the car would still not start unless the key was attached to the correct fob.
Read full answer
Feb 12, 2023 • Rover Cars & Trucks
1helpful
1answer

Strange problem with my car The car does not start when the engine is cold
Clean Throttle Body and MAF. Make sure the air filter and all the pipework are connected. Check Spark plugs for condition and gap.
Read full answer
Feb 05, 2023 • Proton Cars & Trucks
0helpful
1answer

Proton Gen2 2008 When i Start my proton RPM meter go direct to 8k?how can i fix the problem.
The crankshaft sensor in error will make this happen. Replace a new sensor problem will fix.
Read full answer
Oct 07, 2018 • Proton Cars & Trucks
0helpful
3answers

How can you bypass an antitheft system on a 2002 tdi jetta?
If it is not a new key fob, it sounds to me like the immobilizer is activated. So, all the lights on the dash are working now? Is there a flashing key on the dash lights? One of the resets that works is put the key fob in, and turn ignition on without starting it, and leave it 15 minutes. And try again.
Read full answer
Jul 25, 2014 • 2002 Volkswagen Jetta TDI
0helpful
1answer

Immobilzer problem proton gen2
The ignition key holds a sort of RFID chip. If you open it to change remote control battery or you dropped it to pieces and the chip comes off, you will not be able to start your car. Get your spare key and use it to start. The key that cannot be used to start has to be replaced/reprogrammed.
Read full answer
Mar 07, 2014 • Proton Gen2 Cars & Trucks
0helpful
1answer

I have a proton gen2 and the immobilzer has immobilized the car. When I put the key in to turn engine on nothing happens
Get your spare key and use it to start. If it starts, the key that cannot be used for starting has to replaced/reprogrammed. Don't forget to come back and rate my post.
Read full answer
Mar 07, 2014 • Proton Cars & Trucks
0helpful
1answer

When i start my car thier is a time that it will not start. and its appear in the scantool engine immobilizer system mulfunction.
check immobilzer wires at key switch for fault/key chip fault
Read full answer
Mar 11, 2011 • Toyota Land Cruiser Cars & Trucks
16helpful
2answers

Immobilizer
If there is a blinking car icon with an "X" over it. This icon means the Immobilizer has been activated and hence won't allow the car to start. It could be due to a bad SCU, Start Control Unit. The SCU is actually the ignition switch on these cars.
Most of the time it's triggered by the anti-theft system..You can try this trick i learned that the dealers won't tell you...try locking and unlocking of the doors five times with the remote to reset the immobilizer and see if this helps.
Good luck..i hope this helps...please take a minute to rate me a fixya.
Read full answer
May 11, 2009 • 2000 Volvo S40
0helpful
1answer

Locking mechanism is broken on driver's door.
If the valet key is not programmed to the Immobilzer system, it should start the car, but it will shut off. This is only if the car has an Immobilizer system. If your locksmith unlocked the car without the door key, then use the key to unlock and disarm the alarm in the door. If you triggered the alarm, the starter will be disabled till a unlock signal from a remote or the door is actually unlocked with a key. If that cannot be done, your only solution right now is to tow it to the dealership and have them make a master key and check the door locks for proper lock/unlock commands so the alarm will arm and disarm correctly.
Read full answer
Apr 25, 2009 • 1998 Audi A6
Not finding what you are looking for?

View Most Popular

Cars & Trucks

Related Question

PROTON GEN2 1.6 GLX CAMPRO CONNECTING RODS SETTINGS

  • Proton Cars & Trucks

544 views

Ask a Question

Usually answered in minutes!

Popular Questions

Torque settings for proton gen2 cylinder head&connecting rods

Proton Cars & Trucks

Where is the fuel pump relay located on my proton wira 4g92p

Proton Cars & Trucks

Proton Gen2 1.6 S4PH engine Cylinder Head Torque Settings. Cam Timing Marks Existing marks not clear When I aligned the marks prior to remove cylinder head the piston was half way up the sleeve not t

Proton Cars & Trucks

Wiring diagram for a Proton Gen 2

Proton Cars & Trucks

Proton wira

2002 Proton 400

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Proton Experts

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66855 Answers

Kardoc

Level 3 Expert

7503 Answers

john h

Level 3 Expert

29494 Answers

Are you a Proton Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...