What years rear end will fit '99 Sierra 1500
SOURCE: replace rear axel bearing on 4x4 5.3 Litre gas engine
Loosen differential cover and let oil drain. Remove cover, remove U lock from axel. Pull axel out. Remove bearing seal then bearing. Install new bearing, seal and reinstall axel. Reinstall U lock and new cover gasket. Fill with 75-90wt gear oil. Now I know that sound pretty straight forward. But there are some things to remember. The U lock can be difficult to remove sometimes. The most important thing is the seal, you will need to make sure it gets seated correctly and not torn when installing axel.
SOURCE: what transmission will fit in an 89 gmc sierra?
if it has a 4.3 liter motor a 86 to a 97 if it has a 350 motor a 81 to a 96 will work hope this helps
SOURCE: 2003 sierra rear brake rotors
there is many kind of brake system of ur truck here i will send u everything about the brake and i hope its help
Rear Brakes JC3
Rotor Discard Thickness*
18.50 mm/0.728 in
Rotor Minimum Allowable Thickness After Refinish
19.0 mm/0.748 in
Rotor Thickness (new)
20.0 mm/0.787 in
Rotor Maximum Allowable Lateral Runout
0.05 mm/0.002 in
Rotor Maximum Allowable Scoring
1.50 mm/0.059 in
Rotor Maximum Allowable Thickness Variation
0.025 mm/0.001 in
Rear Brakes JC4
Rotor Discard Thickness*
28.50 mm/1.122 in
Rotor Minimum Allowable Thickness After Refinish
29.0 mm/1.142 in
Rotor Thickness (new)
30.0 mm/1.181 in
Rotor Maximum Allowable Lateral Runout
0.05 mm/0.002 in
Rotor Maximum Allowable Scoring1
.50 mm/0.059 in
Rotor Maximum Allowable Thickness Variation
0.025 mm/0.001 in
Rear Brakes JH2
Rotor Discard Thickness*
28.50 mm/1.122 in
Rotor Minimum Allowable Thickness After Refinish
29.0 mm/1.142 in
Rotor Thickness (new)
30.0 mm/1.181 in
Rotor Maximum Allowable Lateral Runout
0.05 mm/0.002 in
Rotor Maximum Allowable Scoring
1.50 mm/0.059 in
Rotor Maximum Allowable Thickness Variation
0.025 mm/0.001 in
Rear Brakes JH6
Rotor Discard Thickness*
27.50 mm/1.082 in
Rotor Minimum Allowable Thickness After Refinish
28.0 mm/1.102 in
Rotor Thickness (new)
29.0 mm/1.141 in
Rotor Maximum Allowable Lateral Runout
0.05 mm/0.002 in
Rotor Maximum Allowable Scoring
1.50 mm/0.059 in
Rotor Maximum Allowable Thickness Variation
0.025 mm/0.001 in
Rear Brakes JH7
Rotor Discard Thickness*
28.5 mm/1.122 in
Rotor Minimum Allowable Thickness After Refinish
29.0 mm/1.142 in
Rotor Thickness (new)
30.0 mm/1.181 in
Rotor Maximum Allowable Lateral Runout
0.05 mm/0.002 in
Rotor Maximum Allowable Scoring
1.50 mm/0.059 in
Rotor Maximum Allowable Thickness Variation
0.025 mm/0.001 in
* All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this Specification. After refinishing the rotor, replace any rotor that does not meet the minimum or discard thickness specifications.
SOURCE: need to replace brake line from rear axle forward
Chanses are it broke behind the gas tank wear it runs along the frame rail. You don't need a diagram to fix that, just unhook it at both ends and break it off or cut it off buy the tank and take the pieces with you to a auto parts store and they will match it up with new line, just take a tape measure and measure from the rear axel to the front block or perportioning valve, and don't worry about the piece behind the tank, just run the new line alongside the old one behind the tank unless you want to pull the tank out.
SOURCE: replace sway bar end links '97 GMC Sierra
if you put your vehicle information in at advanceautoparts.comyou can search sway bar and find parts that you need - there was someinfo missing on which sierra model you have as far as engine size andvin # match but I came to: http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/partlist_Sway-Bar-Link-Kit_78_R|GRPCHASAMS__sway%20bar___
167 views
Usually answered in minutes!
×