2005 Chevrolet Impala Logo

Related Topics:

A
Anonymous Posted on Jan 09, 2018

Does this vehicle have 2 cabin filters?

My mechanic says there is a 2ndary Cabin Filter that requires him to remove the glove compartment to get to. This is in addition to the one that is on the passenger side just underneath the wiper blades. I cannot find anything in the manual that says this car has a 2ndary cabin filter. Please advise.

1 Answer

Brad Brown

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Chevrolet Master 19,187 Answers
  • Posted on Jan 09, 2018
Brad Brown
Chevrolet Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Nov 14, 2008
Answers
19187
Questions
0
Helped
4341967
Points
82259

5 Related Answers

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Nov 22, 2008

SOURCE: cabin air filter

Purchase a Purolator Cabin Filter for your Impala. It comes with complete instructions. The filter is located below the windshield, passenger side. The black plastic cover must be removed to access the filter. You simply raise the hood and remove 3 plastic clips, and the washer hose from it's holders. This will allow you to remove the plastic cover over the filter

Please rate this

Ad

Anonymous

  • 4 Answers
  • Posted on Jan 11, 2009

SOURCE: Cabin Air Filter Location

Empty glove box, remove axcess panel and the open the axcess door, two (2) filters inside,

Anonymous

  • 25 Answers
  • Posted on Jan 31, 2009

SOURCE: How to Fit a Cabin Filter

Hiya...the cabin air filter is located below the front passenger/windshield area.
It's only accessible by standing outside the Equinox with the hood open.
Here's how to do it...(before you pop open the hood)

1) Stand outside at the front-right door area.
2) Just below the front windshield area, pull up a few small black plastic clips that's on the black windshield wiper cowl area- a small flat screwdriver or a special clip-remover tool is handy.
3) Raise the hood up.
4) There may be a triangular-shaped hard foam sound damper at the left side nearby the hood hinge...pull it off if it allow you to work around it with ease.
5) Continue to find a few black plastic clips around the black windshield wiper cowl area.
6) Gently pull up the black windshield wiper cowl cover with care not to bend it too hard during removal.
7) You should see the cabin air filter inside that's held in place by a black rectangular box inside.
8) There's 2 black tabs that holds the cabin air filter in place.
9) Insert your finger or tool to pry the cabin air filter away from the tabs.
10) Remove old cabin air filter.

Remember to reinstall the clip parts back into place when you're finished.

Anonymous

  • 25 Answers
  • Posted on Apr 05, 2009

SOURCE: where and how to change cabin filter chevy equinox

Hiya...the cabin air filter is located below the front passenger/windshield area.
It's only accessible by standing outside the Equinox with the hood open.
Here's how to do it...(before you pop open the hood)

1) Stand outside at the front-right door area.
2) Just below the front windshield area, pull up a few small black plastic clips that's on the black windshield wiper cowl area- a small flat screwdriver or a special clip-remover tool is handy.
3) Raise the hood up.
4) There may be a triangular-shaped hard foam sound damper at the left side nearby the hood hinge...pull it off if it allow you to work around it with ease.
5) Continue to find a few black plastic clips around the black windshield wiper cowl area.
6) Gently pull up the black windshield wiper cowl cover with care not to bend it too hard during removal.
7) You should see the cabin air filter inside that's held in place by a black rectangular box inside.
8) There's 2 black tabs that holds the cabin air filter in place.
9) Insert your finger or tool to pry the cabin air filter away from the tabs.
10) Remove old cabin air filter.

Remember to reinstall the clip parts back into place when you're finished.

Anonymous

  • 218 Answers
  • Posted on May 04, 2009

SOURCE: Cabin air filter in my 2001 Monte Carlo

OPEN THE HOOD.ON THE PASSENGER SIDE BELOW THE WIPER IS PANEL TO BE REMOVED.IT IS IN THERE

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Does a 2006 jeep commander have a cabin air filter?

Yes, some 2006 Jeep Commander models do have a cabin air filter. However, it depends on the specific trim level and options installed.
To check if your 2006 Jeep Commander has a cabin air filter, you can consult the owner's manual or contact a Jeep dealership or mechanic. If your vehicle does have a cabin air filter, it is typically located behind the glove compartment and can be replaced easily.
1helpful
1answer

I recently acquired a 2006 Mitsubishi Galant SE. I attempted to change the cabin air filter only to discover the location is sealed. How do I change the filter?

This filter is an optional item and may or may not be dealer installed.

The procedures in this article are typical of most Misubishi vehicles.

REMOVAL & INSTALLATION

1. The filter is located behind the glove compartment. Open the glove compartment, (disconnect damper rod, if equipped) push on the sides while pulling down to release the latches. Allow the glove box to swing down on its hinges.

2. Remove the 2 air filter screws.

Some vehicles may not have an installed cabin air filter, but may have a sealed filter compartment. In such cases, the sealed compartment will need to be punched-out and a new air filter frame acquired before a cabin air filter can be installed.
NOTE:
The filter is optional and may not be installed in all vehicles. If the filter compartment is sealed as shown, use a flat head screwdriver to punch through the perforated plastic cover. Some vehicles may not have the filter frame pre-installed in the compartment. If so, accquire the filter frame before installing filter element.

3. Remove cabin air filter. Remove the old filter frame (if present) by sliding it out towards you. Remove old filter from its frame and install new filter, ensuring that Air Flow arrow is pointing down.

4. Install in reverse order.
0helpful
1answer

Need to Clean the Air-Condition Filter in Suzuki Alto 2006

Changing the cabin air filter is fairly easy to do if you follow this how-to guide. New vehicles usually come equipped with one or more cabin air filters. A cabin air filter provides fresh air through the passenger compartment side vents. Step-By-Step Guide
  1. The first thing you need to do is locate your owner's manual to find out if your vehicle is equipped with a cabin air filter. If you can't find the information, then your car is probably not equipped with a cabin air filter. However, if you would like to be sure, call your favorite parts store and they can provide you with the information.
  2. When you purchase the new cabin air filter, be aware that there are 2 types of filters. One is called the particulate; the other is called the activated charcoal. The particulate filters out road dust, bacteria, mold spores, pollen and other pollutants. The activated charcoal filters the above mentioned and filters harmful gasses and odors. People who drive around in gridlock or have an odor problem might consider buying the activated charcoal, though it is more expensive.
  3. After purchasing the filter, make sure you have your eye protection, gloves, ratchet, socket and screwdriver before beginning the procedure.
  4. Remove the glove compartment. Usually, vehicles are equipped with bolts and screws to hold the glove compartment in. Your glove compartment may have tabs as well, so be careful when removing the compartment and use the tabs to remove.
  5. After removing the bolt and the screws, remove the glove box frame.
  6. Locate the filter housing. Look for a removable plastic filter cover.
  7. Remove the filter. Most under-dash filters can be removed simply by opening the filter door.
  8. Before installing the new filter, vacuum the filter chamber to remove any excess particles. You may also take a damp cloth and wipe the inside of the air filter chamber to clean out unwanted dust and particles.
3helpful
1answer

Replace cabin filter f150 lariat 2006

This is one of those topics that I have seen both ways.

1. The 2004 was the only MY to include an airfilter.
2. The late build 2004 to 2008 could have a dealer installed cabin air filter kit installed.

So don't be shocked if you go fishing for it, and it is not there. On to the directions :

Open the passenger-side glove compartment box. Remove all of the items currently stored in the glove box

Notice two screws on the inside ceiling of the glove box securing the glove box to the dashboard. Use a flat-head screwdriver to remove these screws. The glove box will now be loose. Wiggle the box off the dashboard and allow it to hang.


Locate the rectangular plastic housing; this is where the cabin air filter is stored. Remove the housing cover by pulling it out of place. Remove the dirty cabin air filter by sliding it out of the clips securing it in place. Discard the dirty filter.


Slide the replacement cabin air filter into the retainer clips. Push the filter housing cover back into place until you hear it lock. Place the glove compartment back into place. Replace the two screws that secure the glove box in place and tighten with the screwdriver. Place the items back into the glove box and close the box.
0helpful
1answer

Heater/defrost does not change position. windows fog, fan motor running as should just will not let air into cabin.

get the cabin air filter of ur endeavor changed by following method.
Procedure to Remove the Old Cabin Filter First off, you need to open the glove compartment; you'll see two screws on top of the glove compartment and two at the bottom of it.

Remove each one of them one by one with the help of a Phillips screwdriver, and then unhook the stop bar which you can find on the right side of the glove compartment .

Next, pull the glove compartment out - while pulling the glove compartment out we disconnect the light wire .

Now, you should be able to see two tabs on both sides of the cabin filter which we press towards the middle of the compartment and then we remove the cabin filter cover . After this, slide the filter out of the housing .

Putting the New Filter In Place Now, you can easily insert the new filter in the filter housing making sure the "up" arrow printed on the filter points towards the roof of the Endeavor and then we replace the cabin filter cover.

Next, insert the glove compartment back into the dash and while it is half way through you need to reconnect the light wire.

Finally, reconnect the stop bar over the hook and finally replace the four screws to hold the glove compartment firmly in place. And, that's it - you've just learned how to change cabin filter in Mitsubishi Endeavor.
9helpful
2answers

Locate cabin air filter for 2006 kia sorento

Hi. The 2006 Kia sorento is not equipped wiht a cabin air filter. Only the 07 and 08 sorentos are equipped wiht this filter. With that said; If your vehicel had a filter, it would be located just behind the glove box. If you were to access it for replacment, you would Open the glove box and remove the side stops so the glove box can swing fully down and hang on its hinges. Once that is done, you will be able to access to the cabin air filter and the clips which hold it in place.
0helpful
1answer

Pleaase advise how to install the Cabin Filter on a Hyundai 2003

Open glove compartment. Press inward at both sides of the glove compartment, then lower the glove compartment.Remove the lower side instrument panel and crash trim pad. Remove the four glove compartment upper cover retaining screws, then the cover. Remove the two glove compartment retaining bolts, then the glove compartment. Press on the cabin air filter cover tab, then remove the cove
Remove the cabin air filter from the blower unit opening. Install a new cabin filter, ensuring the air flow marking is facing in the proper direction. Install the cabin air filter cover, ensuring the cover is properly installed.
Position the glove compartment to the instrument panel, then install the two retaining bolts. Install the glove compartment upper cover. Install the lower side instrument panel crash pad. Lift the glove compartment into position. Close the glove compartment.
7helpful
1answer

Where is the cabin air filter located at and how do i get to it.

It will either be behind your glove box, or will be located under your hood by the firewall.

    Behind the Glove Compartment
  1. Open the glove compartment and remove all the items from inside of it.
  2. Remove the glove compartment assembly retainer screws with a Phillips head screwdriver. Refer to the repair manual for your specific year and model series BMW for the exact location of the screws or carefully look around the perimeter of the interior glove box assembly to locate the screws.
  3. Locate the lower trim panel retaining screws behind the glove box assembly. Remove the screws with a Phillips head screwdriver and then remove the panel.
  4. Remove the foot-well air duct.
  5. Loosen the retaining screws of the control module box to all you to lower it down.
  6. Turn the cabin air filter panel retaining knob counterclockwise to open the panel. Pull the filter removal tab outward to remove the filter.
  7. Use a shop vac to clean out any noticeable debris from the cabin air filter housing interior.
  8. Insert the new filter and reverse the order to reassemble the foot-well air duct, the trim panel and the glove compartment assembly.
  9. Under the Hood
  10. Open the hood and locate the cabin air filter housing. The housing is located near the cowling on the top section of the firewall. Some models place the housing in the middle of the cowling, on both sides--left and right--of the cowling or on the passenger side cowling. Removal of the cowling and placing the windshield wipers in the upward position may also be required on certain models. Some 7-Series BMWs place the filter housings on both the left and right side undercarriage of the hood.
  11. Release the cabin air filter duct clamp. This can either be released by unclipping the air filter duct by pressing a retaining lock with your fingers or using a flathead screwdriver to pry off a retaining rod.
  12. Lift the cover upward--or downward on hood-installed 7-Series BMWs--to reveal the cabin air filter.
  13. Remove the cabin air filter from the air duct. Vacuum the air duct with a shop vac.
  14. Insert the new cabin air filter(s) and reassemble.
1helpful
1answer

Cabin filter

1 Tools needed are a Phillips screwdriver and a socket wrench. Open door to passenger side of vehicle. 2 Under the glove compartment is a kick plate cover held in place by four screws. Remove the screws and take off cover. 3 The door to the cabin filter is now visible. Remove screw in door and unhinge. 4 Remove the first filter by pulling straight down. Remove the second filter by sliding forward and pulling down. Replace with clean cabin filters. Reattach door and kick plate cover.
Good luck and hope this helps. 
2helpful
1answer

Cabin filter 2000grand cherokee 4.7 liter v8

Your cabin filter on this vehicle should be behind the glove ox, gtly remove your glove bx and you should see the compartment for the filter behind it. Hope this helps.
Not finding what you are looking for?

73 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29494 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...