Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Feb 11, 2014

1995 Chevy 350 5.7. O2 sensor unpluged and running better

Could my computer chip be bad?

1 Related Answer

Anonymous

  • 15935 Answers
  • Posted on Mar 26, 2009

SOURCE: 1998 chevy pickup V8 130.000 miles running very

The Exhaust Gas Recirculation (EGR) valve is an important part of the exhaust circulation system of a vehicle. EGR valves have been in use in the United States since the 1960s, when car companies were seeking ways to increase the efficiency of vehicles while also decreasing pollution. When the EGR valve is clogged or malfunctioning, it can cause irregularities in engine performance such as rough idling or valve knock, indicating that the EGR valve should be inspected.
The EGR valve works by routing a small amount of exhaust back into the combustion chamber, where it can be reused. This is done for a number of reasons. The primary reason is that a certain temperature is required in the combustion chamber, and exhaust is much warmer than air taken in from the outside. As a result, the engine need not work as hard to heat the combustion chamber to optimal temperature. The second reason is that the use of an EGR valve helps to reduce nitrogen oxides, which will combine with elements in the atmosphere to form smog.
Many EGR valves are mechanical, and simply have a small valve which opens to allow exhaust into the combustion chamber and closes when it is not necessary, and to keep the air mixture optimal for combustion. Some mechanical versions will not open until there is sufficient back pressure, ensuring that the valve will not be open when the engine is idle or warming up and needs a higher concentration of oxygen for combustion. Electronic EGR valves are also available, and use electronics to regulate the valve.
If the EGR valve is stuck open, it will essentially cause a vacuum leak, leading to inefficient combustion, rough idling, hesitation, and sometimes stalling in extreme cases. This is because the car cannot combust on carbon dioxide from the tailpipe alone-it needs atmospheric oxygen as well. If the combustion chamber is flooded with exhaust from an open EGR valve, it will not function properly. To check and see if the EGR valve is stuck open, have someone idle a parked vehicle with the brake on while you examine the plunger shaft to see if it is stuck open.
If the EGR valve is stuck closed, emissions of nitrogen oxides will rise, and the car may start to knock. Spark knock happens when the fuel mixture in the combustion chamber ignites before it has been reached by the explosion in the cylinder, resulting in a disruption of the engine timing. In this instance, the engine should be warmed up and revved to see if the EGR valve will move.
In both cases, simple repairs are possible. The EGR valve can be clogged, and a simple cleaning of a mechanical EGR valve may solve the problem. In the case of an electrically controlled EGR valve or a more complex mechanical problem, replacement of the valve may be needed. The EGR valve is an expensive motor vehicle component, and care should be taken to ensure that it needs to be replaced rather than repaired. A reputable mechanic should advise you appropriately.
Failure to repair or replace the EGR valve will not lead to a life threatening condition, although it will reduce the life of your car and increase the potential emissions. Especially in areas which require smog testing, an automobile with a malfunctioning EGR valve may not pass.


Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

Rough idle chevy 350

Have you checked/replaced the O2 sensor(s). They produce the data that your computer reads. Bad/clogged O2 sensors will trick the ECU into running lean/rich.
0helpful
1answer

If the catalytic converter is clogged will it make car miss out not want to go(1999 chevy lumina)

could be ether of these. try unplugging the front o2 sensor see if it runs better. if so its that o2 try unplugging the rear o2 if its better its that o2. by unplugging it the computer just selects an average input of a good o2. could also be many other things but start with that and I would change the fuel filter maybe its clogged
0helpful
1answer

Idle and run problem with 1995 Chevy C2500 2 Wheel Drive, 350 Truck

check fuel pressure and injectr/s condition
indicates that you have faulty / leaking injectors /seal
0helpful
1answer

1987 CHEVY IROC Z28 350 TPI- RUNNING RICH, LOTS OF CARBON BUILT UP ON THE INTAKE, BAD FUEL MILAGE

I'd be looking for a few things there. First, make sure that the temperature sender is working. If not, the computer thinks the engine is always cold so it sends more fuel even though it's not needed. Next, make sure that there aren't any exhaust leaks ahead of the O2 sensor. That will cause the sensor to think that the actual mixture is lean, again asking for more fuel. Also check that the O2 sensor is good. Out of range can do the same thing. There are other more complicated causes but those are the most common.
0helpful
1answer

Miss fires at ideal smells like to much fuel out of exhaust. Runs better at higher rpm. 2000 Pontiac Grand am 2.4L

If it improves with rpm, I would suspect a stuck injector (not closing) causing your engine to run rich, or a bad temperature sending unit. You should check for fault codes (they will do this for free at Autozone). You will most likely have a code for a bad oxygen sensor. Don't replace it until you correct the rich fuel mixture with the bad one unplugged. The rich mixture is the cause of the bad O2 sensor, not the symptom.
I you unplug the O2 sensor the ecm will substitute a generic value, allowing you to correct the real issue without destroying another O2 sensor. They are not cheap.
You can verify a stuck injector cyl by cyl by inspecting the plugs. If they all look the same, you may want to unplug the cold start injector and see how it runs.
1helpful
1answer

M1998Chevy Silverado 1/2 ton 4WD Z71 is running extremely rich on the #1bank. My local garage put it on a scope and said the computer was bad. Is there any way of resetting the computer or does it need...

If the computer is bad than it will need to be replaced.

I would make sure the bank 1 sensor 1 O2 sensor is not stuck lean. I have run into this many times. Usually you can unplug the sensor and have the vehicle runs better and watch the bank 1 short term fuel trims settle down a bit. You will need a higher end scan tool to view O2 sensor data and fuel trim data so its not necessarily DIY friendly but maybe something for the shop to check if they have not checked already.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

2helpful
1answer

1995 chevy silverado 350 TBI V8 standard powerloss

have you checked the filter, i know you state the fuel lines are clear though. likely fuel injectors have lost flow. the TBI injectors can be cleaned, but i usually just replace them. but check them using a timing light hooked to the coil wire for timing of each injector spray. the pattern under the light should be even and conical shape, no major spatter. if one shows low volume, the other one should be replaced at same time, it will save you having to change it when you put brand new next to old one a have same problem again. only replace with brand new, i've had 7 bad remanufactured injectors on one truck at one point in time, only replace with new!
2helpful
1answer

O2 sensor problem

I have a 97 gmc sierra .This truck is the same as the chevy ok.Its a 350 5.7 liter 4x4 Z71.I took it to auto zone which was my first mistake.They put it the scanner and said bad O2 sensor.Ok so which one is it i said.They dont know.Well there four (4) O2 sensors in this truck i hope you know that.I had to replace all four of them before i had to take it to a real shop.It seems the fuel pump i replaced a week earlier with an auto zone fuel pump was bad.Ive changed my feul pump 4 times now and have 235000 miles on still running.You need to get your fuel pressure checked.It should be 65 psi to start it and 55 psi to run it.If the pressures are good it could be a different O2 sensor or maybe the mass air flow senor.My last option would be the fuel pressure regulator because it seems to be a waste of time and money.I would get that fuel pressue checked first.Good luck.
0helpful
1answer

Buick lesabre nightmare 2

  • The PCM doesn't even see the O2 sensor until engine temp has reached operating temp,the vehicle goes from open loop when cold,to closed loop when warm,where the PCM uses the O2 sensor to measure the rich/lean of the exhaust content,and from that,adjust fuel richness to achieve 14.7 to 1 air/fuel ratio.So when cold,the O2 sensor is out of the picture anyways.When unplugging sensors,it can be deceitful.The PCM has a program whereas,if a critical sensor (such as the mass air flow) is somehow damaged and out of the picture,the PCM will substitue a generic value that will allow the engine to stay running.So,by unplugging the MAF,it did try to run on it's own better than plugged in,there's the problem area.The vehicle is running better with the MAF unplugged,because the MAF is likely bad,and the PCM is substituting it's generic value when it IS unplugged.Something to recheckThe PROM update is a newer program for the PCM,and likely won't fix it unless the PCM is bad.I would try a good used PCM as a last or later resort,because i have seen my fair share of defective PCM's too.I have taken some PCM's apart,and found capacitors that had gone bad and leaked all over the circuit board,mostly Honda and Mitsubishi and Chrysler though.Good luck,keep me posted.
Not finding what you are looking for?

732 views

Ask a Question

Usually answered in minutes!

Top GMC Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...