Unable to program my keyless remote for 2000 chevy malibu

There is no manual on board procedure to program a keyless remote to this vehicle. This vehicle requires special equipment be connected to the vehicle to program the remote. Dealer fix

Unfortunately your 2009 Chevy Malibu key fob does not have any self programming procedures. You have to have a professional program this key fob to your vehicle. I do have a couple money saving tips for you:

1) Purchase your Malibu key fob online at https://www.keylessentryremotefob.com/Chevrolet-Malibu-Remotes-and-Keys-s/3733.htm

2) Call a locksmith for programming. They are usually more affordable and they come to you.

You must take it to the Chevy dealer.

you need to call the nearest chevy dealer with you vin, and get the part number from them, there are 2 numbers on the back of the remote, see if they match what the dealer tells you. Have an automotive locksmith program, should cost about 75.00 to do.

1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.

Thanks for using Fixya - a 4 THUMBS rating is appreciated for answering your FREE question.

You need to take your car to a chevy dealer because they have the procedure for that, if tou call they wont help you by phone, they charge afee for that.

PROGRAMMING
Method One
Sit in driver's seat
Close all doors
Press and HOLD UNLOCK button on door lock switch.
Insert and remove ignition key twice. Do NOT turn ignition switch
Insert ignition key a third time and leave it in the ignition switch. Do NOT turn ignition switch
Release door lock switch.
A chime will sound three times indicating remote programming active
Press and HOLD the LOCK and UNLOCK buttons on each remote for 5 seconds
A chime will sound twice for each remote: indicating successful programming
Remove the key from the ignition switch to exit programming
Method Two
Remotes can be programmed using diagnostic equipment.

Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the DOOR unlock switch.
While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds , the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters.
Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation

Dealer only If you find a different means let me know

It took me a few attempts to program a new keyless remote for my 2002 Chevy Blazer.
Insert key into ignition but don' turn it yet. While holding down the UNLOCK switch on the door, the trick is to cycle the ignition ON OFF ON OFF as quickly as possible then release the UNLOCK switch. If done correctly the door locks will cycle 1x to acknowledge. Then hold both the unlock and lock buttons down on the remote for about 15 seconds. The locks should cycle again to confirm...Hope this helps.