Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Feb 09, 2014

Amp light on in 88 crown victoria.put new alternator & battery & ends up stalling.

5 Related Answers

Anonymous

  • 261 Answers
  • Posted on Nov 24, 2008

SOURCE: 2000 Ford Crown Victoria

when you hold the accelerator does the vehicle stay running? if so the problem is in ithe IAC idle air control motor, take a small screw driver and using the handle tap the iac motor and usualy the motor will kick in and the vehicle will run fine then if the problem is rectified replace the IAC

Ad

Anonymous

  • 1 Answer
  • Posted on Apr 03, 2009

SOURCE: Battery wont charge in my 1997 ford crown victoria

In the 1995 and later Crown Victoria's, there is a fuse in the fuseblock that controls the alternator's charging of the battery. If that fuse is blown, your car will drain the battery and cut off as you stated.
Check the fuse block under the hood and the one located on the left driver side above the hood pull.

Anonymous

  • 155 Answers
  • Posted on Jul 06, 2009

SOURCE: battery not charging

check the fuses in the POWER DISTRIBUTION BOX under the hood, There is a 75A in-line fuse and #11 - 15A fuse see if they are good.... test your alt. loom for opens, and cables .....hope this helps...GL

Anonymous

  • 141 Answers
  • Posted on Aug 09, 2009

SOURCE: How does one reconnect the air suspension

You probably have a leak in the system. Did "they" check the lines and air suspension? "They" probably disconnected the compressor to keep it from burning out from overuse. You need to fix the leak before reconnecting or the compressor will wear out very quickly.

Anonymous

  • 102 Answers
  • Posted on Sep 23, 2009

SOURCE: how to trouble shoot starting system 98 ford crown victoria

Also check to see if there is power in the start wire form the ignition switch, the wire is a white wire with pink stripe, most likely not a common problem, but still something that could go wrong. this wire will feed the starter relay under the hood...

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

After replacing the alternator airbag light and battery light stays both lights go off and car dies.

electrical issues since replacing alternator & battery - Mazda 6 ...

forum.mazda6club.com > Mazda6 (Atenza) > Newbie Section
Dec 24, 2010 - Exclamation Battery Light after Replacing with New Alternator ... TheBattery Light stays on after I start the vehicle. It comes up after ~2-3 secs of ...

Battery light flashing, air bag light on, after alternator pulley ...

https://forums.tdiclub.com/showthread.php?t=343786
Feb 11, 2012 - Battery light flashing, air bag light on, after alternator pulley changeTDI 101. ... Almost a week later I am driving home and the battery light flashes on, then off, .... Seat belt light stays on, no air bag light. cjharris02892, TDI 101 ...

Battery Light Due to Damaged Alternator Wire Harness ...

repairpal.com > Problems > Ford > Crown Victoria
Battery Light Due to Damaged Alternator Connector on Ford Crown Victoria ... how can i turn off the airbag light on a 1991 crown victoria made by ford ... the battery light onreplace alt and batt light still what else can it be? thaqk. it sat for two weeks when we had snow i used my truck staqrted car light comes on and stays on.

Airbag light = bad battery - Maintenance, Recalls and T


1helpful
3answers

I have a 2006 crown Vic and it's not tring to start change the alternator have a new battery

Is the red light in the center of the dash , on top of dash panel not instrument cluster flashing when trying to crank the engine over ? If yes you have a anti theft system problem ! If the light is not flashing you can check for power an ground an PCM control at the starter relay in the under hood battery junction box ! Bottom of relay or side show pin numbers ! Pin's 30 & 86 should have battery voltage ! Pin 87 - ground through the starter , Pin 85 should have nothing unless cranking engine over . The PCM supply's a ground here energizing the starter relay ! You can also test this by using a test light . The clamp end to battery positive , the point end touch to pin 85 relay socket while cranking ! Test light should light !
0helpful
1answer

Interiorfuse box diagram for2002 crown vic

Changing the Battery & Alternator won't cause those issues

When people come to a site like this and say they HAD something
done & NOW have problems

You know who put them there--THE SHOP YOU WENT TO
1helpful
1answer

2000 crown victoria won't start after i got a new battery and altenator. What can the problem be?

The starter or it's solenoid

The new battery & alternator didn't
but the problem in there
1helpful
1answer

1994 crown vic, not PI, is not charging. Put in

there is a alternator fuse on the relay center under the hood that is a large fuse rated i think at like 140 amps check it it probably blew
2helpful
2answers

95 Ford Crown Victoria. Battery light came on. Bought a new battery. After driving for awhile battery light cuts on and off. Radio, heater, and lights keep cuting on and off. When I step on the gas after...

easiest check is to put a voltmeter on the battery posts. Should be 14 volts or over with engine running. If not alternator may have 1 or more bad diodes.

Also, clean all the battery connections, incluidng small wires on poitive post, if present.
0helpful
1answer

1988 Ford Crown Vic Strange Idle (Getting Worse)

i am trying to install an aftermarket temperature guage with capillary tube into my 1988 crown victoria ltd 5.0 efi. where does the capillary tube mount?
Not finding what you are looking for?

281 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...