Question about 1991 Toyota Corolla

1 Answer

CONROD TORQUE SPECIFICATION FOR 5A-FE ENGINE

I NEED TO KNOW THE TORQUE SPEC FOR CONNECTING ROD NUTS,CYLINDER HEAD BOLTS,MAIN BEARING CAPS BOLTS,FYLWHEEL BOLT,CAMSHAFT BOLT AND BIG ENDS CUP BEARING.

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Ays as well as response to this question UVB the radiation. But it always recommended Vita Luminance while using safe sunscreen as per your skin sensitivity. Zinc oxide sunscreens are constructed from metallic zinc that recently been oxidised. It absorbs the UV rays and hence protects your skin from acquiring it contact with sun sun light.



http://utrimcleanseblog.com/vita-luminance/ Vita Luminance


Injection Free Solution For Youthful Skin

Posted on Mar 04, 2016

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 92 Answers

SOURCE: torque specs for 1998 tercel 1.5L

Main Bearing Cap Torque-42 Ft. Lbs.
Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 Degrees
Rod Bearing Nuts-29 Ft. Lbs.

Hope this helps

Posted on Sep 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 3.8L what is the aspec diagram and tourque for the racker arm


Hi Juan, I'm AL the owner of Big As Auto Repair

Below is the torque specs for the rocker arm as you requested.

SPECIFICATIONS - TORQUE

DESCRIPTION N·m Ft. Lbs. In. Lbs. Camshaft Sprocket-Bolt 54 40 - Camshaft Thrust Plate-Bolts 12 - 105 Forged Connecting Rod Cap-Nuts 54 +¼ turn 40 +¼ turn - Cracked Connecting Rod Cap-Bolts (Refer to 9 - ENGINE/ENGINE BLOCK/PISTON & CONNECTING ROD - INSTALLATION) Crankshaft Main Bearing Cap-Bolts 41 +¼ turn 30 +¼ turn - Crankshaft Main Bearing Cap Cross Bolts (3.8L) 61 45 - Crankshaft Oil Seal Retainer Rear-Bolts 12 - 105 Crankshaft Damper-Bolt 54 40 - Cylinder Block Drain Plugs 20 15 - Cylinder Head-Bolts (Refer to 9 - ENGINE/CYLINDER HEAD - INSTALLATION) Cylinder Head Cover-Bolts 12 - 105 Flex Plate to Crankshaft 88 65 - Engine Mounting (Refer to 9 - ENGINE/ENGINE MOUNTING) Powertrain Torque Strut 54 40 - Exhaust Manifold-Bolts 23 - 200 Exhaust Crossover Pipe-Bolts 54 40 - Intake Manifold - Lower-Bolts 23 - 200 Intake Manifold - Lower Gasket Retainer-Bolts 12 - 105 Intake Manifold Upper-Bolts 12 - 105 Lifter Yoke Retainer-Bolts 12 - 105 Oil Filter Attaching Fitting 54 40 - Oil Cooler Attaching Fitting 27 20 - Oil Filter 20 15 - Oil Filter Adapter-Bolts 28 - 250 Oil Gallery Plug 27 20 - Oil Pan-Bolts 12 - 105 Oil Pan Drain-Plug 27 20 - Oil Pressure Switch 23 - 200 Oil Pump Cover Plate-Screws 12 - 105 Oil Pump Pick-up Tube-Bolt 28 - 250 Oil Dipstick Housing-Bolts 48 35 - Rocker Arm Shaft-Bolts 23 - 200 Spark Plug 16 12 - Thermostat Housing 12 - 105 Timing Chain Case Cover -M8 Bolt 27 20 - -M10 Bolt 54 40 - Water Pump-Bolts 12 - 105 Water Pump Pulley-Bolts 28 - 250
Should you need extra help visit my website here: http://www.bigasautorepair.com/

Apr 15, 2015 | 2005 Chrysler Pacifica

2 Answers

What the torque specs. For a 2002chevys10 4.3vortex mains and rod bearing


Torque Specs Database

Type: Dim: Length: Head: Nut Grade: 20 Ft-Lbs 240 In-Lbs 27.12 N-m Connects: Connecting Rod To Engine Block Years: All Vote Record: Vote Note: Vortec - Rod Cap Nuts - 2 Steps: 20 FtLbs; +70degs

http://ww2.justanswer.com/uploads/ZZdaryl/2009-06-14_153454_torque.pdf

Main Bearing Cap Bolt 4.3L Step 1 15 ft lbs (20) Step 2 Additional 73 Degrees

i don't know if that's correct for main bearing caps since another link states it's much higher

4 3 Vortec Piston Specs eHow

hopefully a GM guy will chime in to confirm the main bearing torque

the rod bearing torques are the same on all the other links

Mar 25, 2015 | 2002 Chevrolet S-10

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

1 Answer

Main bearing cap torque 6g74


Torque Specifications

air intake plenum 11-14 ft lbs.

camshaft bearing cap 14-15 ft lbs.

connecting rod nut 37-38 ft lbs.

camshaft sprocket bolt 66-67 ft lbs.

crankshaft pulley bolt 108-116 ft lbs.

cylinder head bolts 65-72 ft lbs. ( 3.0L) 76-83 ft lbs. (3.5L)

drive plate ( flywheel ) 53-55 ft lbs.

exhust manifold 11-16 ft lbs.

intake manifold 11-15 ft lbs.

main bearing cap 55-61 ft lbs.

rocker shaft 14-15 ft lbs.

valve cover 27-35 in. lbs.

throttle body bolt 84-108 in. lbs.

May 17, 2012 | 1996 Mitsubishi Montero Sport

1 Answer

V6 T3000 need torque specs has throttle body injector


3.0L and 3.5L V6

Torque Specifications

air intake plenum 11-14 ft lbs.

camshaft bearing cap 14-15 ft lbs.

connecting rod nut 37-38 ft lbs.

camshaft sprocket bolt 66-67 ft lbs.

crankshaft pulley bolt 108-116 ft lbs.

cylinder head bolts 65-72 ft lbs. ( 3.0L) 76-83 ft lbs. (3.5L)

drive plate ( flywheel ) 53-55 ft lbs.

exhust manifold 11-16 ft lbs.

intake manifold 11-15 ft lbs.

main bearing cap 55-61 ft lbs.

rocker shaft 14-15 ft lbs.

valve cover 27-35 in. lbs.

throttle body bolt 84-108 in. lbs.

Aug 15, 2010 | 1994 Mitsubishi Montero

1 Answer

Torque specs for 1.5 kia rio connecting rod


TORQUE SPECIFICATIONS kia rio
Cylinder Head Bolts:
(21.7ft.lb) or (3.0kgf.m) 90?

May 22, 2010 | 2001 Kia Rio

1 Answer

Complete torque specs. for entire engine. rods, mains, heads. etc.


Assuming 3.0 V6, per my manual:

All in FT pounds torque,unless noted:

Main bearings: 60
Connecting rod bearing cap nuts: 34
Rocker arm shaft bolts 180 INCH POUNDS
Intake manifold: 168 INCH POUNDS
Exhaust manifold nuts: 18
Crankshaft vibration dampner bolt: 112
Cam shaft sprocket bolts: 70
Head bolts: 76 - 83
If you need others please let me know, when working with Aluminum parts go easy as they can strip easy.
Please let me know if this helped,
Tom

Apr 30, 2010 | 1991 Mitsubishi Mighty Max

1 Answer

Torque specs for the main bearings, connecting rods and heads


Here you go...

Connection Rod Nuts: 37-38 Ft Lbs.
Main Bearing Caps: 55-61 Ft Lbs.
And Head Bolts...

1st - step; - 80 ft./lbs. 2nd - step, loosen all bolts; 3rd - step; - 80 ft./lbs.
69de06e.png

Jan 24, 2009 | 2000 Mitsubishi Montero

3 Answers

Need torque specs


Torque sequence:
Step 1: Torque 29 to 34 Ft/Lbs
Step 2: Torque an additional 90 to 120 degrees

Oct 14, 2008 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
1991 Toyota Corolla Logo

1,813 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...