Fuel filter? Traveling and vehicle has no power, idles fine, but at highway speeds gives 2 seconds of power followed by 2 seconds of deceleration. Fuel Filter? can I replace in parking lot?

I didn't see any mention of the fuel filter being changed. Nor do I know your driving habits to help determine the possible problem.

That being said, I would change the fuel filter as I've had 2 vehicles that acted somewhat the same way as you described.

Both vehicles idled fine. They both ran good up to the point when there was more of a load put on the engine, i.e., up a hill or attempting to get up to speed on the highway.

Hope this helps.

Check engine fan operation and make sure radiators not packed with dirt and debris.When your on the highway you have the speed you are traveling at air cooling the radiator.

The idle air control solenoid is very common to quit working. The only other thing would be a large vacuum leak.

I'm not specifically familiar with your truck, but I would check with a dealer to ensure there is no inline filter before taking the part store's word for it. While most vehicles have a pick up filter in the tank for big stuff, I've never seen a car without an inline filter for micro-particulate. The part store you called may simply not carry it, or may carry a desk help person who doesn't know what they're doing (happens all the time). Other possible issues for your surging could be that you have a sticky injector that isn't opening/closing properly, that your automatic trans is acting up (if you have one), or a pressure regulator in the lines (my wife's car also does this because the part that is supposed to hold fuel pressure in the line is bad (as a result it starts hard unless you let the pump "prime" the pressure just before starting) and so it surges just a little with the fuel pump's cycling when driving at freeway speeds. I think you're on the right track with an inline filter though and would try that first.

The PO 316 is still misfires om first 1000 revolutions
so the shop did a poor job for you on resolveing the
cylinder misfires

Try a diffferent shop

Have to clean the MAF Sensor & replace upstream
oxygen sensors if over 100,000 miles

Need the correct oem spark spark plugs/any brand

No reason the gas filter should be clogged unless it was in
the car for 10 years

Fuel pressure should be checked

Need to check for cylinder misfires on a road test of 20
miles or more with professional software in Mode#06

Here is the OBD2 emission system drive cycle test procedure.
Engine coolant temp must be below 70c (158f) before starting the engine for either the first or second trip
The fuel level should be less than 1/2 full
First trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" for at least 10 seconds (not more than 5 min)
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary.
End of first trip. Turn the key off the begin the second trip.
Second trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" add four gallons of fuel
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary. I especially like the part where they want you to add four gallons of fuel. Not three gallons, not five gallons, four gallons. Gotta love those Nissan engineers. ...and of course they state that if the trace is not followed exactly (i.e. you botch the acceleration/deceleration) you have to start all over again from scratch

JUST SAW, the most common cause of your engine dying and backfiring while driving on highway would be low fuel pressure. check fuel filter for foreign debris. filter may be clogged or restricted, also a weak fuel pujmp. the other thing could also be a stuck e.g.r. valve, this would have some exhaust carbon deposit stuck on the seat of the valve producing a vacuum leak, but it would not idle properly.faulty fuel pump would give you a good engine idle but would starve for fuel at high highway speeds, when the engine needs for fuel for proper operation.

takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Could be a bad coil. Sometimes when a 'bad' coil heats up it will fail to work properly. When it fails and shuts the vehicle off, this gives it time to cool back down and resume proper operation. Does it run at normal highway speed during that 20 minutes? If not then it could be a clogged fuel filter. A clogged fuel filter will let the vehicle run at idle but will starve the engine at higher rpm's.

Loss of fuel pressure.
1. Clogged fuel filter (replace anyway)
2. Fuel pressure regulator (stays open)
3. Fuel pump