Drivers rear window will not go up or down, stuck half way up

You say the driver window works? wouldn't be a main fuse or fusible link then -driver door locks and window wouldn't work either. Each door has a module inside (computer) . The driver door has a circuit breaker power feed an a fuse DDM fuse 10amp located in rear junction block circuit breaker is located in under hood maxi fuse block. The circuit breaker also feeds battery voltage to the other door modules too. PDM - passenger door module fuse 10amp located in the instrument panel fuse box and the RDM - rear door module RDM fuse 10amp located in the rear fuse box - under the back seat.

Each power window is connected to a permanent magnet motor. The motor raises or lowers the glass when the door module applies voltage to the motor. The direction the motor turns depends on the polarity of the supply voltage provided by the associated door module. The 2 front doors have their own separate modules. The rear seat contains a single module, which controls both of the rear power windows.
A serial digital communications link, called the simple bus interface, is used for communications between door modules and the driver's door power window switches. The use of serial digital communications allows the use of a single wire to convey switching information between the power door lock switch and the driver's door module (DDM). The serial communication is also used in order to transmit switching information from the DDM to the other 2 door modules.
The door modules apply battery voltage of the correct polarity to the respective window motor when any local, or power door lock switch, UP switch is operated, driving the window up. Battery voltage is applied to the respective window motor in the opposite polarity when any local, or power window switch, DOWN switch is operated, driving the window down.

Driver Door Module (DDM)
The driver's door module (DDM) directly controls the driver's door window motor and the express down window feature. The DDM sends window UP/DOWN messages received from the power door lock switch to the passenger door module (PDM) and to the rear door module (RDM) over the simple bus interface (SBI) line. The DDM also contains a class 2 data link which communicates with the other vehicle system modules. The left front power door locks and the outside power mirror are also controlled through the DDM.
Passenger Door Module (PDM)
The passenger door module (PDM) controls the passenger's door window motor. The PDM controls the passenger's door window directly from the right front power window switch or from instructions over the simple bus interface (SBI). The right front power door locks and the outside power mirror are also controlled through this module.
Rear Door Module (RDM)
The rear door module (RDM) controls both of the rear door window motors. The RDM controls the rear windows directly from the rear door window switches or from instructions over the simple bus interface (SBI).

Some cars are designed this way. Either the doors are not wide enough at the bottom to accommodate the size if the window, or they made the opening smaller to make it so a small child could not fall out of the window. Many vehicles have rear windows that only lower half way.

The power windows on your vehicle are controlled by an electronic control module , as are the power mirrors !
Power Window System Components
The power window system consists of the following components:
• Driver door module (DDM)
• Passenger door module (PDM)
• Body control module (BCM)
• LR power window switch
• RR power window switch
• Window up and window down relays in each of the rear passenger window switches
• Window lockout switch
• Reversible power window motors in each of the doors (circuit breaker protected)
• LT DOOR CB 25A (System power for left rear window)
• RT DOOR CB 25A (System power for right rear window)

Your best bet , take your vehicle to a qualified repair shop.

Before you replace anything, inspect the connector pins in both the driver's door switch and the passenger door switch. If you don't find any problem with these connector pins, replace the driver's door control switch.

Sounds like dirty contacts inside the control switch. You can disassemble it and try cleaning the contacts with electrical contact cleaner or maybe rubbing alcohol with a swab.

It may be that it is not on the track properly or your power window motor is old and tierd and can take the window down but it doesn't have the juice in it any more to bring it back up. replace the motor and it will work. This problem happened to me in my '76 ford ltd and a new motor fixed it.

Window regulator has failed. Inside door panel needs to be removed to access motor/regulator

If neither switch works it is a bad connection at the motor or bad ground or a bad motor. Remove the door panel unplug the motor push the switch and see if there is 12volts on the wires if there is the motor is bad There are small brushes in the motor that go bad tap on the motor while pushing the switch if it works that way replace it

most of the time it is wires in the drivers door that break in the loom