Suburban K2500 Door lock is in the locked position with the door open, cannot close the door, re-set?

the child safety lock is normally a small lever at the edge of the door and has no effect on closing a door
it just prevents the door from being opened on the inside
what may have happened is that the door lock mechanism is in the 1/2 closed position and will not allow full lock (close) to occur
place a small screw drive under the latch or tongue of the lock and pull out as you press the door handle as if opening the door
that should then place the latch in the correct position for latching the door when closed properly

remove the rear seat cushion or bottom to gain room to remove the door panel. good-day!

hi jerome
I have the procedure for Toyota auto lock, is worth to try it
AUTOMATIC LOCK SETTING
1) Step in the vehicle and make sure that all doors are closed completely
2) Insert the key into the ignition key cylinder.
3) Wait for more than 5 seconds.
4) After turning the key to the ACC position, turn the key from the ACC to the
ON position 5 times within 10 seconds (Last position : ON).
? Status Monitor LED will illuminate for 30 seconds.
Note : In case you implement 6 times or more by mistake,
action steps 6)-8) you made will be canceled.
Please retry from step 2).
5) While the LED is illuminated :
• Open and close the driver's door 2 times.
• Turn the key to the ACC position.
? LED will continue illuminating.
? Indicator lights will flash 2 times.
Ignition controlled door lock ON :
6) While the LED is illuminated:
• Open and close the driver's door 1 time.
• Turn the key ACC-ON-ACC 1 time (Last position : ACC).
? Indicator lights will flash 1 time.
? LED will extinguish.
Ignition controlled door lock OFF :
6) While the LED is illuminated :
• Open and close the driver's door 2 times.
• Turn the key ACC-ON-ACC 1 time (Last position : ACC).
? Indicator lights will flash 2 times.
? LED will extinguish.

For Doors not getting open with remote or key problem,there are help links provided below.Click the link below to go through its procedure and troubleshoot the problem:----
drivers side front door will not open from inside or outside?

http://technoanswers.blogspot.com/2012/01/ford-f-350-crew-cab-drivers-side-front.html

----------

Car door will not close?
http://howtobyme.blogspot.com/2011/11/car-door-will-not-close.html

--------

All power door locks not working ?
http://howtobyme.blogspot.com/2011/11/all-power-door-locks-not-working-on_14.html

----------

Repairing car Door lock Actuator?
http://howtobyme.blogspot.com/2011/11/repairing-car-door-lock-actuator.html
---------------
How to Access car door panel?
http://howtobyme.blogspot.com/2011/11/how-to-access-car-door-panel.html

----------

Vehicle door panel components?

http://howtobyme.blogspot.com/2011/11/vehicle-door-panel-components.html

---------
Truck Door will not close?

http://schematicsdiagram.blogspot.com/2011/12/ford-truck-door-will-not-close.html

-----------
Where is Cars Door control Module located?

http://schematicsdiagram.blogspot.com/2011/12/where-is-cars-door-control-module.html

--------
Power door locks not working?

http://schematicsdiagram.blogspot.com/2011/12/power-door-locks-not-working.html

-----------
Door ajar light stays on?

http://technoanswers.blogspot.com/2012/01/door-ajar-light-stays-on.html

----------
Door locks not working?

http://technoanswers.blogspot.com/2012/01/door-locks-not-working-on-ford-explorer.html

----------
Front Door dis-assembly diagram?

http://repairhelpcenter.blogspot.in/2012/02/front-door-dis-assembly-diagram-for.html

---------
Rear Door dis-assembly diagram?

http://repairhelpcenter.blogspot.in/2012/02/rear-door-dis-assembly-diagram-for.html

--------
How to test Power door locks?

http://repairhelpcenter.blogspot.in/2012/02/how-to-test-power-door-locks.html

--------
Doors will not open with Remote?

http://schematicsdiagram.blogspot.in/2012/02/lexus-doors-will-not-open-with-remote.html

--------

How to replace Door Hatch ?
http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-hatch-on-acura-integra.html

---------

How to remove Doors?

http://repairhelpcenter.blogspot.com/2011/11/how-to-remove-doors-on-acura-integra.html

-------`-

How to Replace Doors?
http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-doors-on-audi-a4-and-vw.html

--------

Remote will not unlock Rear door?
http://schematicsdiagram.blogspot.com/2011/12/remote-will-not-unlock-rear-door-on-gmc.html

--------

Door locks or windows not working on car?
http://schematicsdiagram.blogspot.com/2011/07/door-locks-or-windows-not-working-on.html

--------

This will help.

Thanks.

Your problem is the door thinks that it is already locked and closed. You need have the sliding door unlocked, have someone pull the handle as if they were going to open the door and then use a tool to "Open" the latch that normally would hold the door closed.

Hi!!
I believe your alarm is in the PASSIVE MODE, here is how it works.

PASSIVE MODE Setting (Arming) Anti-Theft System The system will automatically set 30 seconds after following methods are performed: Remove ignition key from ignition switch. Exit vehicle, and close all doors. After performing this, anti-theft indicator on left side of instrument panel will light continuously for about 30 seconds. After 30 seconds, anti-theft indicator will blink once per second. When system is set, doors cannot be locked or unlocked using door lock control switch.
CANCELING THE ALARM AND REPROGRAMING MAY SOLVE YOUR PROBLEM.
Canceling Anti-Theft System Setting (No Alarm) When system is set (armed), but alarm is not sounding, use one of following methods to cancel system setting:

• Unlock left or right front door using key.
• Unlock all doors using remote keyless entry system.
• Insert key in ignition switch and turn to ON position (this is operative only when anti-theft system has not been triggered).

HERE IS HOW TO REPROGRAM THE ALARM IN CASE YOU NEED TO RESET IT.
PROGRAMMING
PASSIVE MODE NOTE:Initial mode is passive mode off. If there is a different signal in middle of programming, signal is invalid.
Programming Passive Mode Off

• Remove ignition key from ignition key cylinder. Ensure all doors (including back door) and engine hood are closed and unlocked. Perform all of following methods within 30 seconds:
• Lock or unlock any door with key or remote keyless entry system.
• Open driver door.
• Lock and unlock driver door lock knob 3 times.
• After performing this, system should start force lock after 2 seconds. Perform all of following methods within 20 seconds:
• Unlock driver door lock knob.
• Close and open driver door 2 times.
• Lock and unlock driver door lock knob.
• After performing this, system should start force lock after 2 seconds. Passive mode should now be off.

Programming Passive Mode On

• Remove ignition key from key cylinder. Ensure all doors, engine hood and luggage compartment door are closed and unlocked. Perform all of following methods within 30 seconds:
• Lock or unlock any door with key or remote keyless entry system.
• Open driver door.
• Lock and unlock driver door lock knob 3 times.
• After performing this, system should start force lock after 2 seconds. Perform all of following methods within 20 seconds:
• Unlock driver door lock knob.
• Close and open driver door 4 times.
• Lock and unlock driver door lock knob.
• After performing this, system should start force lock after 2 seconds. Passive mode should now be on.

If you need further assistance, please provide an email address to send more info on your security system
Good Luck!! A 4 THUMBS UP rating would be greatly appreciated for this solution. Thank you for using FixYa!!

open the door and look at the lock check to see if the lock is shut, it will look like a ( C ) if it is in the correct position for a open door. If the lock has locked while the door is open it will be in a closed position. if this has happened you will need a screw driver , and when while the door is open insert the key, and insert the screw driver into the lock mechnism and pop it open as you unlock it with the key

sounds like you lached the door
use a screw driver or some such tool
lift the outer handle and slip your tool in the middle of the lock hole in the door flip the lach open wile holding handle up

this problem i have repaired many times.. it is normally a broken wire in the flexible rubber tube between the door and the doorjamb from years of flexing back and forth when you open and close the door.. i hope that helps

It sounds to me ( correct me if I'm wrong ) like the door latch on the side vertical edge of the door is in the LOCKED POSITION. In order to unlock it perform the following. First electrically with the LOCK button UNLOCK the locks. Now with one hand hold the OUTSIDE DOOR HANDLE IN THE OPEN POSITION, while at the same time FLIPPING OPEN THE LATCH. All Done . Now you can close the door. Hope this helps