1996 Chevrolet K1500 Logo
Posted on May 26, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

4L60E Shifts fine in 1st, 2nd, & 3rd but will not shift into OD

I have a 1996 Chevy 4x4. It's a 350 with the 4L60E. The trans shifts 1st thru 3rd fine won't shift to OD. I just changed the convertor, fluid and filter. I was driving the truck and turned it off, started driving again and would not go into OD. Do you have any suggestions?

1 Answer

Harvey N Tawatao

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Chevrolet Master 3,854 Answers
  • Posted on May 26, 2009
Harvey N Tawatao
Chevrolet Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Apr 05, 2009
Answers
3854
Questions
0
Helped
2796130
Points
16501

The EMC detected and problem so it's in limp mode, As long as it's in limp mode the 4th and OD will not activate. Take care not to burn up the transmission by running it hard while your in the limp mode.
Your going to have to get the truck scanned to clear any codes and why there are DTC codes. Auto Zone scan for free and most auto shops charge $10.00 to $20.00 to scan sine they want the business.
If you want to clear the codes your self you can put the ignition to the run position and pull the ECM (Batt) fuse out for 20 sec and place it back in then start the truck. It may stall but let it, just start it again and this would have cleared all the DTC code history.
The transmission should be running fine unless there is a problem and the service engine light will be on again and you'll be in limp mode still with an updated DTC in the ECM.
Good luck and hope this helps.

  • Terry Yeager Oct 11, 2013

    Ok Thanks,,I think I will tackle this myself.Again the Transmission shifts fine,just won't go into OD.

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Lost 3rd gear and overdrive on my 92 crown vic

I have a 92 Crown Vic first and second works fine reverse works fine when it shifts in the third gear it goes to slipping and overdraft can you help me fix this problem thank you
0helpful
1answer

2003 Chevy Tahoe, No First or Fourth Gears, not shifting, which trans solenoid(s) do I need to replace?

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

http://www.shoeish.com/uploader/images/460le.gif

Good luck and thank you for using fixya
2helpful
1answer

1996 gmc jimmy will not shift to 3rd gear

Hi, It may be in LIMP mode.

What is "limp-home mode" ? This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Common failures on 4L60E, symptom any possible repair:

Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under-hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter :ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Trans seems noisy when moving in 1st and Reverse, noise goes away instantly if you shift to N or the trans goes into 3rd gear: Reaction planetary is worn out due to high miles or insufficient lubrication. Not a critical failure, but not a good sign either. R&R sooner rather than later.

3rd gear starts, can manually shift through all gears. When car has been turned off for a bit, then back on it will run normally.: VSS dropoff w/ Hi-stall converter. The rpms are too high, but VSS is showing no movement. Happens after a tire burning take-off. Doesn't store a code, will not throw a CEL (I've heard that it will store a code if it happens 3 or more times). Cure: Reprogram PCM for VSS dropoff -- PCMforLess knows about it.

If you can get the Jimmy for no more then $500.00 and the engine sounds good and body is good, you may want to invest in the repair of the jimmy. Also note that to have a close look at the fuel line along the frame on the drivers side just by the back doors, the line is know to corroded there on all the SUV's
0helpful
1answer

Chevy s10 2.2 liter transmission problem

a number of issues. Tcc regulator bore worn out, the infamous check ball seat it hammered badly, or/and calibration issues. I have seen all three issues on the same trans - often!
0helpful
1answer

1993 4l60e - Shifts hard on the 1-2 shift, works fine otherwise.

Did you change the transmission filter and gasket as well as the transmission oil before running your truck.
0helpful
2answers

1995 Chevy S10. The transmission (4L60E) has been

HI YOU MAY HAVE A BAD IGNITION SWITCH OR YEST A BAD SHIFT SOLENOID 3-4
2helpful
1answer

4L60E won't shift to 3rd on 1993 Chevy Blazer 1500

Sounds like you have a bad shift solenoid. Not sure if the Chevys are a solenoid pack, or seperate, but it will need to be replaced.
1helpful
1answer

4L60E won't shift to 3rd on 1993 Chevy Blazer

Hello;
It sounds as though your trans is going out. How is reverse? If reverse is real strong then you may just have a solenoid going out. Drop the pan and change the oil and filter if you are comfortable doing that. Inspect the pan for metal shavings and contaminents. Otherwise it would need to go to a shop for repair.
Thanks;
Rich
RPM Northwest
3helpful
3answers

4L60E Shifts fine in 1st, 2nd, & 3rd but will not shift into OD

check fluid conditon and level, may be a faulty soleniod
0helpful
2answers

95 GMC Jimmy 4L60E no 2nd or OD 4L60E

do u have any trouble codes for the trans? u need to find out to see if a shift solenoid (possible 2-3) has failed.
Not finding what you are looking for?

2,144 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...