Question about 2004 Hyundai Santa Fe

1 Answer

MAF wiring diagram 2004 hyundai santa fe sensor

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 8,984 Answers
Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: camshaft position sensor location

crank sensor is a component used in an internal combustion engine to monitor the position or rotational speed of the crankshaft. This information is used by engine management systems to control ignition system timing and other engine parameters. Before electronic crank sensors were available, the distributor would have to be manually adjusted to a timing mark on the engine.

The crank sensor can be used in combination with a similar camshaft position sensor to monitor the relationship between the pistons and valves in the engine, which is particularly important in engines with variable valve timing. It is also commonly the primary source for the measurement of engine speed in revolutions per minute.

Crank sensors in engines are usually comprised of magnets and an inductive coil. They are principally based on the Hall effect. Common mounting locations include the main crank pulley, the flywheel, or occasionally on the crankshaft itself.

Some engines, such as GM's Premium V family utilise crank position sensors which read a reluctor ring integral to the Harmonic Balancer. This is a much more accurate method of determining the position of the crankshaft, and allows the computer to determine within a few degrees the exact position of the crankshaft (and thereby all connected components) at any given time.

Posted on Dec 27, 2008

Anonymous

  • 6 Answers

SOURCE: how to change spark plugs on hyundai 2004 2.4L

Remove the plastic cover that goes over the engine (the one with the Hyundai logo).
At this point, you will see the cables that goe to each fo the spark plugs.
Noting their position, remove them.
The spark plugs are ready to be removed, turn counterclockwise and replace with manufacturer recomended ones.

Posted on May 16, 2009

Anonymous

  • 84 Answers

SOURCE: Change serpentine belt 2004 Hyundai Santa Fe

it uses a spring loaded tensioner.use a breaker bar to rotate the tension and it should just come off.if u need a pic or anything else to do it let me know,

Posted on Oct 05, 2009

tracer_steve

Steven Mitchell

  • 68 Answers

SOURCE: 2004 Hyundai Santa Fe 2.7 all wheel. Crank sensor

Hi

On the 2.7 engine it is located beside the starter. You will have to remove the starters heat shield to gain excess to the crank sensor.

Posted on Jan 31, 2010

Rene J Solis

  • 1796 Answers

SOURCE: Where is the alarm system

The Control module is located behind the cigarette ashtray. Remove ashtray and the trim around it, it has two screws on the sides and two on top. The set switch is located in the control module. Here are some diagrams. Good Luck!! Don't forget to rate this Post!!!

bdd1696.gif

c97476c.gif

65dc524.gif

3031fa2.gif

Posted on Sep 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a wire diagram to wire CD player in 04 santa Fe with out factory plug


You can get all
wiring diagrams, torque specs, electrical diagrams, controls etc. at www.reliable-store.com

Mar 10, 2018 | 2004 Hyundai Santa Fe

1 Answer

Mass air flow sensor voltage high


Hot-Wire-Type MAF Sensors
  1. To check the MAF sensor's voltage signal and frequency, connect a voltmeter across the MAF voltage signal wire and ground wire.
  2. Start the engine and observe the voltmeter reading.
  3. On some MAF sensors, this reading should be 2.5 volts.

Sep 29, 2016 | 2004 Hyundai Santa Fe

1 Answer

2004 hyundai santa fe parked it last night, went to use it today and it doesn't accelerate, engine runs fine, no warning lights on dashboard lit, can put it in gear and move it, but absolutely no...


The 04 Santa Fe came with three different engines. 4 cylinder (2.4 lit), and two different V6's (2.7 lit & 3.5 lit). The 2.4 & 2.7 use throttle cables connected directly to the throttle plate, but the 3.5 uses ETS (Electronic Throttle System) which uses two sensors (APS & TPS) and a control module (ETSCM). APS=Accelerator Position Sensor, TPS=Throttle Position Sensor, ETSCM= Electronic Throttle System Control Module. There are different diagnostic procedures for each system.
Go to www.hmaservice.com and register your vehicle by VIN #.. you'll then have access to wiring diagrams, shop manuals, service bulletins, campaigns, illustrations and procedures, etc.

Sep 10, 2011 | 2004 Hyundai Santa Fe

1 Answer

Do you have a wiring diagram of a hyundai car?


Here is the wiring diagram of the Hyundai Santa Fe
tinualbinale_0.gif

Jun 03, 2011 | 2004 Hyundai Santa Fe

1 Answer

Diagram for serpentine belt


For the 2004 Hyundai Santa Fe:
I do not know if you have the 2.4L DOHC In-Line 4-Cylinder, 2.7L DOHC V6, or the 3.5L DOHC V6 Engine; however the Link below has all three Diagrams.

Click on the following: direct, free Link. It has the Belt Diagrams for your 2004 Hyundai Santa Fe. It also has very helpful Instructions and Directional Diagrams.

Let me know if this helped...
http://www.2carpros.com/car_repair_information/year/2004/make/hyundai/model/santa_fe/2004_hyundai_santa_fe_drive_belt_routing_diagram.htm

Apr 23, 2010 | 2004 Hyundai Santa Fe

1 Answer

CAN YOU PROVIDE A GUIDE TO CHANGING A TIMING BELT ON A HYUNDAI SANTA FE 2004


Go to www.hmaservice.com and register (veh by VIN). You'll then have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Sep 02, 2009 | 2004 Hyundai Santa Fe

1 Answer

Are 08 hyundai santa fe and tucson desame stereo wiring harness?


NOPE! . Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Jun 29, 2009 | 2004 Hyundai Santa Fe

2 Answers

Need to fit temperature fuel sensor on santa fea


There is a fuel temp. sensor. Mine went bad on my 2005. $39.00. Its in the gas tank. you can access the sensor from under the back seats. Mine came up as a check engine fault code. Also, it had no impact on engine performance. Hope that helps.

Jun 06, 2009 | 2004 Hyundai Santa Fe

Not finding what you are looking for?
2004 Hyundai Santa Fe Logo

Related Topics:

395 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...