1994 Buick LeSabre Logo

Related Topics:

ROBERT MARRERO Posted on Jan 09, 2014

Transmission modulator how to replace

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

tip

I get code p0700 after an OBDII scan.

P0700 Transmition Control system is the transmission control module.
The transmission control module is a separate computer module, you need to read codes stored on transmission control module.

If there are no transmission code stored, then there is a bad Transmission Control Module (TCM) ground circuit or a bad TCM. In that case the ground to TCM must be tested, and TCM eventually replaced.

Faults that can cause troubles when shifting from first to second gear are : transmission fluid, speed sensor, TPS, transmission shift solenoid, gear box problem, TCM, neutral switch, torque converter problem.

The best thing to do is scanning TCM codes.
tip

My car does not shift in second gear.

Hi.

The first thing to do is replacing the transmission fluid. Metal debris inside the transmission box gets mixed with fluid and can cause similar problems.

The automatic transmission uses throttle position sensor to determine position and opening of throttle.
IF throttle position sensor is defective, the car may have problems shifting into one or more gears.

The automatic transmission is controlled by an electronic control module, that is energizing a set of solenoids to shift into gears.
The control module is a rectangular box, often located behind the dash and wired to transmission. The solenoids are attached to valve body,inside transmission.

If a solenoid is defective, or if control module is defective, the car may have problems shifting into one or more gears.

Problems concerning transmission control module, TPS and transmission solenoid are usually detectable reading fault codes stored on the car main control module (ECU/ECM).

Transmission problems are often returning a code p0700 after an OBDII scan.

Stored codes can be retrieved using an OBD scan reader.
If the car auto transmission is not shifting into gear, talk to the mechanic about the problem.
Only when the car has a really high mileage, or when there is a factory problem there is need to replace the gearbox.
A damaged gear box at low mileage is rather unusual.
on Oct 23, 2009 • 1988 Jeep Cherokee
0helpful
1answer

My 1980 caprice wont shift like it not getting proper vacum for transmission

Replace the vacuum modulator valve on the transmission . First off I would test it . You would need to buy a hand held vacuum pump ! and find the vacuum hose at the transmission an test for vacuum there . Do you know what a vacuum modulator valve is ? Google 1980 Chevy Caprice transmission vacuum modulator .
0helpful
1answer

Located transmission vacuum module at on the car 1997 honda accord

images for transmission vacuum

Vacuum Modulator Service.wmv - YouTube

? 6:00
www.youtube.com/watch?v=u7S9mDqWguY
Dec 19, 2011 - Uploaded by GrumpysTravells How to remove and clean the vacuum modulator air filter. ...Transmission modulator replacement (early GM 4T60-E models) -
0helpful
1answer

Code p0106 on a 2006 dodge srinter

i had came code to. with others . Check under seat unplug control module see if it is wet with fluid . cost me $138.00 fee.
Engine light on than next day off may 2 day then on at same place drive kid to school.
issue with transmission fluid wicking up the harness into the control module and causing the module to malfunction. Usually, the harness from the transmission to the ETC module is replaced and the module is replaced provided the leak is repaired. In some cases this may be more than is actually needed but it usually fixes the concern. Transmission fluid does not actually damage the module and can be flushed away with board cleaning solvent or electrical contact cleaner as a first attempt. Always repair the leak before replacing a module.
1helpful
1answer

2004 dodge sprinter trans stuck in low gear . i am trying to locate the trans module

Check under seat unplug control module see if it is wet with fluid . cost me $138.00 fee.
Engine light on than next day off may 2 day then on at same place drive kid to school.
issue with transmission fluid wicking up the harness into the control module and causing the module to malfunction. Usually, the harness from the transmission to the ETC module is replaced and the module is replaced provided the leak is repaired. In some cases this may be more than is actually needed but it usually fixes the concern. Transmission fluid does not actually damage the module and can be flushed away with board cleaning solvent or electrical contact cleaner as a first attempt. Always repair the leak before replacing a module.
http://www.benzworld.org/forums/w163-m-class/1465231-mercedes-repair-maintainance-transmission-etc-tips.html
0helpful
1answer

I have a 2005 dodge 2500 sprinter, the check enginge lite comes on often. It seems to come on more when it is a little damp and cold.

Check under seat unplug control module see if it is wet with fluid . cost me $138.00 fee.
Engine light on than next day off may 2 day then on at same place drive kid to school.
issue with transmission fluid wicking up the harness into the control module and causing the module to malfunction. Usually, the harness from the transmission to the ETC module is replaced and the module is replaced provided the leak is repaired. In some cases this may be more than is actually needed but it usually fixes the concern. Transmission fluid does not actually damage the module and can be flushed away with board cleaning solvent or electrical contact cleaner as a first attempt. Always repair the leak before replacing a module.
3helpful
2answers

How replace a transmission modulator valve on

It is located on the transmission with a vaccume line going to it. There is a clamp with a bolt that holds it to the transmission. It is an easy fix.
3helpful
3answers

2004 DODGE SPRINTER WILL NOT SHIFT OUT OF FIRST GEAR AFTER RE CH

Check your ATF oil level in your transmission and replace filter. After if still came check transmission relay switch and do fault code erase
Not finding what you are looking for?

77 views

Ask a Question

Usually answered in minutes!

Top Buick Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...