Sounds like mass airflow sensor or vacuum leak check intake gasket for air leaks you might have a bad head gasket also check compression
SOURCE: engine overheating
No water pump issues I am aware off, are you sure you bled the air out of the cooling system? If not fill the overflow bottle all the way full, then use a floor jack and raise the front of the car as high as you can ( this allows air to go to top of radiator tank), then run the engine at high idle speed until the cooling fan ( I assume the fan works OK?) comes on, but avoid letting the engine get into the overheat area of the guage, if it does turn it off, run water over the radiator until it cools, check the tank and radiator, top off if you need to and repeat above procedure, if this doesn't work you have some other problem like no or little flow in radiator.
SOURCE: ford ranger truck overheating
I have had this happen with my ranger. Changed everything I could to try to fix the over heating. It turned out that I had a small leak in my head gasket and it was allowing exsaust gas to go into the cooling system witch was over pressurizing it. Also the air from the exsaust will heat up much faster than liquid making your thermostat to read hot and will not be able to blow hot air in the cab because there is no liquid going to the heater core. This happened to me when my blet came off and I tryed to make it home. If you had it over heat for a long peirod of time it may have ripped the head gasket.
SOURCE: My 2002 Ford Thunderbird is
You most likely have air in the system. These things can be a royal pain to get the air bleed out of the system.
Look back next to the brake booster and you will see a rubber tube with a screw cap in the end of it(this is the heater bleed), also on the front of the intake area you will see a black tube with an allen sloted cap.
Remove the slotted cap and screw the screw cc on the rubber tube. Add coolant to the coolant jug allowing the system to equalize until no more coolant can be added. Add as much coolant as possible to the engine fill( the sloted cap near intake). The heater air bleed will remain open.Replace the engine fill cap.Start the engine and turn the heater to MAX position.Close the heater air bleed when a steady stream of coolant comes from it, during engine idle. Allow the engine to idle for five minutes, add coolant to the degas bottle as needed to maintain the cold fill MAX mark.Reopen the heater air bleed to release any entrapped air and close again. Maintain engine speed of 2,000 rpm for 3-5 minutes or until hot air comes from the heater.Return to idle and verify hot air is still coming from the heater. Set the heater temperature setting to 75° F and allow the vehicle to idle for two minutes.Shut the engine off and allow to cool.After the engine has cooled, add coolant to the degas bottle to bring the level to the cold fill MAX mark. This should have the air out of the system.
SOURCE: overheating,reserve coolant tank boiling
Ford 2000 Taurus
To solve the problem you have the things to do in this order;
) When the engine is cold top off the radiator with fluid. (When the pump was replaced the fluid should have been also)
) Make sure the radiator fluid has anti-freeze in it. This is also anti boil also !
) Add fluid to the overflow reservoir.
) Make sure the drive belt was replaced on the water pump.
) With the engine running, you can add fluid to the radiator for the first minute or so. You want to get air pockets out.
) Replace radiator cap.
) Let car warm up. When it's hot you should get the radiator fan coming on.
) When it get hotter the air-conditioning fan may come on.
) If the fan does not come on, the heat sensor is probably bad.
) If all fans come on, and it overheats, you may have a bad thermostat. Trace the upper radiator hose to where it connects to the engine. That's where it located.
Do not operate the engine when it overheats, You will damage the head gaskets and cause radiator fluid to leak into the cylinders.
If you smell radiator fluid in the exhaust fumes, it may already be leaking.
SOURCE: overheating engine in 24 valve 96 ford taurus 6 cyl
the thermostat can be easily changed from up top, the T-stat is located at the engine end of the upper radiator hose under the flange the hose connects to. Make sure u follow manufacturer's cooling system bleeding procedures when you refill after the T-stat is changed out.
The generic method of bleeding air from the cooling system is to use a floor jack and raise the front of the car as high as poss, then fill the coolant recovery tank full and run the engine until it just starts to overheat, high end of normal zone on gauge, then shut the engine down and run cold water over the radiator core, this will self bleed the system and the coolant will be pulled from the recovery tank, repeat as necessary, never let the recovery tank run dry or more air will be pulled into the cooling systeml , if it still overheats then you need to have the head gaskets checked with a gas analyzer for hydrocarbons present in the radiator or recovery tank
835 views
Usually answered in minutes!
×