SOURCE: How do I remove the front door panel to replace the mirror
Normal
0
Disconnect your negative battery cable. Locate and remove
the screws that hold your interior door handles in place (they may be hidden by
snap in, or snap on clips). Remove the interior door handles, then disconnect
the wire clips to the switches. Your panel is held in place by snap in clips;
use a small pry bar to pull them from the door (try to get as close to, or
directly under the clips to prevent them from tearing out of the door panel).
Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.
If you don't have power windows you will have to
remove the manual window crank. It is held in place by a clip on the back side
of the base. To remove the clip, you will need a small hook (kind of like a
knitting needle). Put the hook in behind the base, and grab the clip and pull
it off. To replace it, slide the clip back on the window crank, and snap it
back on the door.
SOURCE: How do I remove a 1995 buick park avenue drivers side door panel?
Normal
0
. First thing, disconnect
your negative battery cable. Locate and remove the screws that hold your
interior door handles in place (they may be hidden by snap in, or snap on
clips). Remove the interior door handles, then disconnect the wire clips to the
switches. Your panel is held in place by snap in clips; use a small pry bar to
pull them from the door (try to get as close to, or directly under the clips to
prevent them from tearing out of the door panel). Once the clips are pulled,
pull the panel upward to remove it from the door.
Install in reverse.
If you don't have power windows you will have to
remove the manual window crank. It is held in place by a clip on the back side
of the base. To remove the clip, you will need a small hook (kind of like a
knitting needle). Put the hook in behind the base, and grab the clip and pull
it off. To replace it, slide the clip back on the window crank, and snap it
back on the door.
SOURCE: 99 Buick LeSabre, how do I remove driver side door panel to replace power window motor?
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
SOURCE: water on passenger side floor of Buick Regal
U need to clear the AC condensation drain, crawl under the car on the passenger side and near the base of the engine firewall u will find a drain pipe, (about 3/4") clear t and the water will stop going on the passenger floor.
SOURCE: how to remove the left front door panel on my 2006 Buick Lucerne
Hi Dear Lov, Remove the plugs from the arm rest and behind them there will be deep seated screws. Push in a long screw driver and remove them. Next lift the window control buttons and when removed from the housings disconnect the electrics. (Keep the switches handy) next take a flat blade tool and starting at the bottom of the door, insert the blade between the panel and the door and gently pull the blade towards you. When the studs pop move to the next until all are released. Lift the panel off and then refit the switch to the cables. Reach inside the door and feel for the operating rods which extend from the handle to the latch mechanism. at each end you will feel plastic clips which will rotate away from the rods when pushed in the same plain. These clips beak easily so be careful. It is worth getting a mirror and flash light and studying them before trying to release them. Check both sides as the mechanism may be different at each end. Once disconnected you will notice two hole opposite the exterior door handle, through which a socket spanner fitted to an extension will fit. Remove the nuts and then remove the handle from the outside. When fitting everything back together make sure the rods are correctly fitted. You may find you need to lift or lower the window, or maybe remove it completely to do the job. Regards John
Testimonial: "Thanks johngee"
242 views
Usually answered in minutes!
×