Where is the purge valve located on a 2004 honda LX?

purge Valve replacement........

https://www.youtube.com/watch?v=1TR9BoHhrJU

DTC P0497: Evaporative Emission (EVAP) System No Flow During Purge
Circuit/System Description
The control module tests the evaporative emission (EVAP) system for a large leak, or a stuck closed EVAP canister purge valve. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge valve OPEN and the EVAP vent valve CLOSED. This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. If the system is unable to achieve the calibrated vacuum level, or the vacuum level increases too slowly, a DTC sets.

Diagnostic Aids
• A loose, missing, or damaged fuel fill cap can cause this DTC to set.
• A stuck closed, blocked, or restricted EVAP canister purge solenoid valve, can cause this DTC to set.
• A blockage or restriction in the EVAP canister purge solenoid valve vacuum supply hose, EVAP canister purge solenoid valve purge pipe, EVAP canister, or vapor pipe, can cause this DTC to set.
• A temporary blockage in the EVAP canister purge solenoid valve, purge pipe or EVAP canister could cause an intermittent condition. Inspect and repair any restriction in the EVAP system.
• To help locate intermittent leaks, use the J 41413-200 Evaporative Emissions System Tester (EEST) to introduce smoke into the EVAP system. Move all EVAP components while observing smoke with the J 41413-SPT High Intensity White Light. Introducing smoke in 15 second intervals will allow less pressure into the EVAP system. When the system is less pressurized, the smoke will sometimes escape in a more condensed manner.
• To improve the visibility of the smoke exiting the EVAP system, observe the suspected leak area from different angles with the J 41413-SPT .
• Observe the Freeze Frame/Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition occurs that caused the DTC to set. This may assist in diagnosing the condition.

PCV valve would have nothing to do with it !
P1443 - Very Small Or No Purge Flow Condition A fuel tank pressure change greater than a minus (-) 7 inches of H 2 O in 30 seconds has occurred with purge (fuel vapor) flow less than 0.02 pounds per minute.

• Blocked fuel vapor hose between EVAP canister purge valve and FTP sensor.
• Blocked fuel vapor hose between EVAP canister purge valve and engine intake manifold.
• Blocked vacuum hose between EVAP canister purge valve-solenoid and engine intake manifold.
• EVAP canister purge valve stuck closed (mechanically).

Check for blockages between the fuel tank, EVAP canister purge valve and engine intake manifold. Check obstructions in the EVAP canister purge valve diaphragm and ports.
Suggest you buy a repair manual if you want to try an fix yourself .Or Go to ford web site Ford Oem1stop com an pay 29 bucks for 72 hours for repair info . Or take it to a qualified repair shop an have it smoke tested . Or goolge purge valve for a pic. an see if you can find it under the hood .

P0441 Evaporative Emission Control System Incorrect Purge Flow,,, EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set. easiest thing to check is the gas cap, remove it, wait a couple of seconds , and put it back on tightly !!

Could be the P0445 - Evaporative Emission Control System Purge Control Valve Circuit Shorted
The EVAP canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the ECM. The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
- Damage harness or connectors to the Purge Control Valve
- The valve circuit is open or shorted
- EVAP canister purge volume control solenoid valve may be faulty

When is the code detected?
- An excessively high voltage signal is sent to ECM through the valve

Try to remember this code number for additional details. Hope this helps, keep us updated.

code p 0441 refers to evaporative emission (EVAP) system --incorrect flow detected ==== causes --- hose connection/s--- intake leak---EVAP canister purge valve replace the purge valve

CODE P1443 - LOW PURGE FLOW OR NO PURGE FLOW CONDITION DETECTED.POSSIBLE CAUSES EVAP CANISTER PURGE VALVE STUCK CLOSED MECHANICALLY FUEL VAPOR HOSE BLOCKED BETWEEN EVAP PURGE VALVE AND THE FTP SENSOR OR BLOCKED BETWEEN PURGE VALVE AND INTAKE MANIFOLD OR VACUUM HOSE BLOCKED BETWEEN PURGE VALVE AND INTAKE MANIFOLD.CANT GIVE PRICE CHECK UNTIL FIND OUT THE PROBLEM.

What are my problems ????? Without testing we'd only be guessing . A lot of electronic's ,software , electrical ,sensors etc.... Hooking up a factory scan tool an viewing data input's an outputs from the different control modules on the vehicle is what should be done by a qualified technician . With any DTC - diagnostic trouble code their are diagnostic test's that need to be done an done correctly so parts are not replaced needlessly . Don't know what kind of scanner was used to pull the code P1440 but this is not a code for your vehicle . I would try a different repair shop .

Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve

P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve

P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve

P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM

P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM

P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM

P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM

P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve

P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor

P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor

P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve

P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve

Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

1. Disconnect electrical connector at solenoid.
2. Disconnect vacuum lines at solenoid.
3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:

1. Position solenoid slot to mounting bracket.
2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
3. Connect electrical connector to solenoid.
   

Purge solenoid location:


EVAP cannister location:

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Evaporative Emission (EVAP) Canister Purge Regulator Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Sealing faulty.
Pipes between Tank Breathing and Throttle Body leaky/blocked.
Hose connection(s).
Intake leak.
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.
VSV connector near air filter box disconnected.