How to remove bumper - 2004 Kia Sedona

Remove the 2 6 mm bolts that attach the bumper to the front corner of the fender. Remove the 2 6 mm nuts that attach the bumper to the frame in the front of the car. Remove the 4 6mm bolts securing the grill. Gently remove the bumper from the front of the car.You could take your car to a mechanic or to the dealership to take off the bumpers on your car and to repair the bumpers.

There are some steps that help you to easily remove Front Bumper :
1. Open the hood of your car.
2 . Look under the edge of the front of the car at the end of the bumper.
Pull the plastic shield down out of the way if it doesn't come off completely. Reach behind the bumper at each corner and you should find a bolt holding the corner of the bumper to the car. Remove these bolts. The bumper should come off.
For more details, click here at https://www.drivenbystyle.com/body-kits-aerodynamics/front-bumpers

have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal

1. Raise and support the vehicle.
   

1. Remove the RH and LH front wheel (1007).
   

1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).
   
   
   
   
   

1. Remove the four front fender brace screws.
   
   
   
   
   

1. Remove the two front fender brace nuts.
   

1. Remove the two plastic screws.
   

1. Remove the seven clip buttons located under the front bumper cover (17D957).
   
   
   
   
   

1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
   

1. Remove the four front bumper cover brace bolts.
   
   
   
   
   

1. Remove the front bumper cover from the vehicle.
   
   
   
   
   

1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).
   
   
   
   
2. Remove the eight front bumper bolts.

1. Remove the front bumper from the vehicle.
   

1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Front Bumper (434230)

Removal
1. Remove the radiator grille.
2. Remove the left-hand front wheel.
3. Detach the fender splash shield from the bumper cover and fender (both sides).
4. Remove the air cleaner intake pipe retaining clip.
5. Detach the air cleaner intake pipe from the air cleaner housing.

1 Rotate the pipe clockwise.

2 Detach the pipe.
6. Detach the bumper cover from the fender and support bracket (both sides).
7. Remove the left-hand side bumper retaining nut.
8. Remove the right-hand side bumper retaining nut.
9. Remove the bumper.

Installation
1. To install, reverse the removal procedure.

Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly. 2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. D. Remove two screws from side of bumper assembly. E. Remove four bumper mounting bolts from under of vehicle. 3. Install rear bumper in reverse order of removal.

It depends on what year your car is,

If it's the pre 02 car then inside the boot there are 2 M10 nuts near the tie down eyes, remove these and then pull the bumper tips outwards whilst pulling the bumper rearwards.

If its the post 02 car then remove the torx screws inside the wheelarch 2each side, remove screw from bottom edge of bumper near to wheel arch each side, remove 2 plastic nuts from lower bumper near spare wheel well, remove rear light clusters then remove the screws behind them, unclip ends of bumper from bodywork and pull rearwards.

remove screws from ends of bumper x4,
remove bolts from under bumper x2
remove indicaters from bumper x2
remove 10mm head bolts from behind where indicater were x4
lift bumper up and out