Question about 2008 Ford Focus
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Your ford focus had options to wheel size, If you have the 15 inch wheel the original tire size is 195/60-15 and if you have the 16 inch wheel option your tire size is 205/50-16. Good luck and hope this helps.
Posted on Jun 11, 2009
To reset the tire pressure light you need to get the tool.
You can get the tool here on link below.
Posted on Nov 09, 2009
2006 Ford Truck Explorer
NOTE: The tire pressure sensor training prcedure must be done in an area without radio frequency (RF) noise. RF noise is generated by electrical motor and appliance operation, cell phones, and remote transmitters.
1. Turn the ignition switch to the OFF position
2. Turn the ignition switch to the RUN position three times, ending in the RUN position. Do not wait more than two minutes between each key cycle.
3. Press and release the brake pedal
4. Turn the ignition switch to the OFF position.
1- Left Front Tire
2- Right Front Tire
3- Right Rear Tire
4- Left Rear Tire
5. Turn the ignition switch from the OFF position to the RUN position three times, ending in the RUN position. Do not wait for more than two minutes between each key cycle.
6. The horn will sound once and the TPMS indicator will flash if train mode has been entered successfully. If equipped, the message center displays "TRAIN LEFT FRONT TIRE." Place the magnet on the valve stem of the LF tire pressure sensor. The horn will sound briefly to indicate that the tire pressure sensor has been recognized by the TPMS module.
7.Within two minutes after the horn sounds, place the magnet on the valve stem of the RF tire pressure sensor. NOTE: If the TPMS module does not recognize any one of the four tire pressure sensors during the tire training procedure, the horn will sound twice and the message center (if equipped) will display "TIRE TRAINING MODE INCOMPLETE." If this occurs, the entire procedure must be repeated from Step 1.
8. Repeat Step 7 for the RR and LR tires. When the tire training procedure is complete, the horn will sound once and the message center (if equipped) will display TIRE TRAINING MODE COMPLETE.
This should help. For now, probably all Fords are like this. And I do not believe that Ford puts sensors in their spares (some GMs do).
Posted on Nov 13, 2009
SOURCE: 2007 FORD EXPLORER XLT
need to set tires at correct pressure you can find a sticker on the inside of drivers door to tell you the correct pressure after you do that it sould reset the light after you drive
Posted on Feb 02, 2010
SOURCE: Tire Monitor & Sensor Fault
Have your tires filled with nitrogen about 10.00 per tire. nitrogen is a dryer, more stable gas that's less prone to changes in pressure due to heat or cold. Nitrogen has long been used in aircraft tires and in the tires of race cars Putting nitrogen in your tires will increase your fuel efficiency because properly inflated tires will reduce rolling resistance, which can mean as much as a 3 percent better mileage than a car with under-inflated tires. Nitrogen will not degrade the interior rubber of the tire or corrode the wheels, since it contains no oxygen or water vapor -- both present in the atmosphere we breathe and pump into our tires. When it comes down to a dollar decision, it's hard to argue that spending as much as $40 for nitrogen in a set of tires is a good fiscal move.Also it will cure a intermitten low pressure light.
Posted on Apr 18, 2010
Tips for a great answer:
Dec 11, 2016 | Ford Cars & Trucks
Dec 08, 2015 | Cars & Trucks
Dec 11, 2014 | Ford Cars & Trucks
Aug 13, 2017 | 2011 Ford Escape
Feb 11, 2012 | 2008 Ford Focus
Jun 05, 2011 | 2009 Ford Fusion
Dec 20, 2010 | Ford Focus Cars & Trucks
Mar 28, 2009 | 2005 Ford Freestar
55 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: