2000 Acura TL Logo

Related Topics:

A
Anonymous Posted on Dec 17, 2013

Acura knock sensor code po325 /3.2 TL

Under steering columb area on left side for obd2 connection

5 Related Answers

Anonymous

  • 1077 Answers
  • Posted on Mar 22, 2009

SOURCE: where is the obd2 plug in on a acura 3.2tl???

Center console,behind a cover,front of trans shifter handle
d205201.jpg

Ad
sheiden9

sheiden9

  • 87 Answers
  • Posted on Apr 04, 2009

SOURCE: 2003 Acura TL, the 5th gear light keeps blinking

I have seen some problems with these sensors going bad when hot replace the sensor and the harness. before you condemm the computer.

sheiden9

sheiden9

  • 87 Answers
  • Posted on Apr 11, 2009

SOURCE: HID BULB REPLACEMENT 2003 ACURA TL DRIVER SIDE

heres the procedure I uploaded it for you click [b][i]HERE[/i][/b]

mecanica03

ROBERT GARCIA

  • 926 Answers
  • Posted on Apr 25, 2009

SOURCE: Code P0505 on 1999 Acura TL

this code make reference to low idle engine,maybe the throttle body is dirty , air filter clogged, vacumm leak , pcv valve clogged, check for thoses

Charlie

  • 280 Answers
  • Posted on Jun 16, 2009

SOURCE: I need a radio code for my 1999 acura TL.

You must contact the parts department of your local Acura dealer to get this code. You will need to show them your car's registration to prove that you are the owner. You may be able to get the code with only the registration and the VIN code (found on the registration). Some manufacturers require the serial number on the radio, which would require that the radio be removed from the car to see the serial number.
Charlie

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Where is bank 1 sensor 2 02 sensor on a 2001 Acura 3.2 tl

Try This..
Stand with the engine belts and pulleys nearest to you. Look down at the engine. Bank ONE is the LEFT side of the engine, Bank TWO is the RIGHT side of the engine. Sensor TWO is positioned AFTER the Catalytic converter, (sometimes referred to as the 'Down Stream' sensor). I think the TL has it mounted right next to the Catalytic Converter Before the exhaust bends to go under the vehicle. This is one of those jobs that is guaranteed to take the skin off at least two knuckles!

**These sensors can be VERY difficult to get loose so make sure your safe under the Vehicle. Use either Axle Stands on both sides of the vehicle, 'Roll On' inspection ramps with blocks under the rear wheels or a professional vehicle lift.**
2helpful
2answers
0helpful
2answers

Acura 3.2 tl makes a noise when started in the morning in cold

that noise is 1 of your belts. there is 3 belts on it. and with the power steering noise I think it is your power steering belt needs to replaced or agjusted
0helpful
1answer

96' 3.2 Acura TL dies while driving now won't

i have posted this solution before, I will give you the short version. On the steering column, under the left side of the cowling, on the opposite side directly across from where the key goes in the ignition,... there is a wire loom screwed to that end with 2 screws, remove this and clean the inside of both sides CAREFULLY, dont break anything. expensive dealer part! just scrape it lightly and wipe a little, carefully re assemble, dont bend it, dont screw it back in too tight, you cant make it go together any closer than it will. This solution solves a number of odd problems attributed to ACURA quitting , battery not charging, lights flickering turn signals not working, a lot of things, so i think everyone should do this to there ACURA, and its EASY!
3helpful
2answers

Where do i plug the code reader in?

In the center console, lift up the ash tray dish. There should be a rubber flap that covers the OBD connector.
0helpful
2answers

Location of the knock sensor on a 2001 Acura TL

The knock sensor is part #8 on the diagram. seems to be inside the engie. call your acura dealer to verify. if it is, it's a lot of work.
http://estore.honda.com/EPC/asp/rjane007.asp#
1helpful
1answer

Location of knock sensor 3.2 1996 acura tl

remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley
1helpful
1answer

Acura TL 2004, code: P0325 knock sensor1 (bank1) circuit malfunction, please help. thanks...

9 times out of 10 it is a faulty sensor. if you have the 4 cylinder engine, v-tech? it will be located on the back of the block next to the oil filter. if you have the V6 it will be under the intake manifold.you can test the knock sensor with a dvm. set your mter on continuity, hook your leeds to the single pin conector and the side of the sensor, you should have a resistance reading.now lightly tap on the side of the sensor with a small screw driver. if the resistance changes the sensor is good
Not finding what you are looking for?

297 views

Ask a Question

Usually answered in minutes!

Top Acura Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

926 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...