Warning lights The red triangle light, check engine light and VSC light are all on, plus the top 1/4 of the display screen is dark except for an outline of a car in the top left.

Not sure if this will help, but my 2002 LEXUS sc430 had this issue, and it turns out that if you plug any scan tool other than the dealer unit in, it will cause this VSC lights to come on. It requires that you reset the "zero point calibration" for the skid system, which is done by first: have car on level ground with less than 1% slope in any direction. Next, follow these directions:

If you receive the "VSC" and "VSC Off" lights on the dashboard after a visit to a mechanic (often an independent mechanic using non-Lexus ODBII equipment), this means your "Zero Point Calibration" has been erroneously reset by a non-Lexus specific ODBII tool. This might especially happen if your state requires state inspection via ODBII, and you take your Lexus to a no-name place (like a Jiffy Lube or something). Follow the steps described in Post #6 in this thread to resolve this issue:
http://www.clublexus.com/forums/gs-2...d-vsc-off.html
Note that where you see a reference to a tool called the "SST 09843--18040", substitute that "tool" for a simple jumper cable (such as a short speaker wire) or a paperclip.
Here is the relevant excerpt from the above thread:
"The solution consists of approximately 15 step .
NOTE:While performing the Zero Point Calibration, do not tilt, move or shake the vehicle.
The vehicle must remain in a stationary condition throughout the entire process.
Be sure to perform the procedure on a level surface with an inclination of less than 1%.
Explanation of symbols:
SST (4-inch wire)
DLC3 (OBD-II connector under the dash)
TS (on the top row,pin number 3)
CG (on the bottom row,pin number 5)
(See picture below)
1. Ensure the shift lever is in the ''P'' range.
2. Turn the ignition switch Off.
3. Using SST 09843--18040, repeat a cycle of short and open between terminals Ts and
CG of DLC3 4 times or more within 8 seconds (refer to the specific vehicle EWD for
TS and CG pin location in the DLC3).
4. Turn the ignition switch ON, do not start.
5. Verify that the VSC indicator light is lit indicating the recorded zero point is erased.
6. Turn the ignition switch OFF.
7. Be sure the terminals Ts and CG of DLC3 are disconnected.
8. Turn the ignition switch ON, do not start.
9. Check that the VSC warning light goes off about 15 seconds after the ignition switch
is turned ON.
10. After ensuring that the VSC warning light remains OFF for 2 seconds, turn the ignition
switch OFF.
11. Connect terminals Ts and CG of DLC3 using SST 09843--18040.
12. Turn the ignition switch ON, do not start.
13. After turning the ignition switch ON, check that the VSC warning light is lit for about
4 seconds and then starts quick blinking at 0.13 second intervals.
14. After ensuring the blinking of the VSC warning light for 2 seconds, turn the ignition
switch OFF.
15. Remove the SST from terminals Ts and CG of DLC3.
16. Drive the vehicle for at least 5 minutes to confirm Zero Point Calibration is complete."
Attached images

VSC ABS and ! lights plus red (!) - Toyota Prius Forum ...

www.priusonline.com/...toyota-prius.../19804-vsc-abs-lights-plus-red.ht...

Jun 3, 2008 - 8 posts - ‎3 authors
If the accumulator fails, you will get a red brake warning light and the pump will now run continuosly until it burns out. ... hydraulic pressure to the brake system and "no"red warning lights. .... Fog Lights, PassGas, Toyota Prius General Discussion, 4, 10-13-2005 09:12 AM ... 11-13-2015 10:01 PM by Tim Lee.

Alarm with Brake Light, ABS, VSC and amber warning lights ' PriusChat

priuschat.com > ... > Gen 2 Prius Care, Maintenance and Troubleshooting

Jul 26, 2005 - Later that same day - I started getting an alarm - as soon... ... Gen 2 (2004-2009) Toyota Prius Forums > Gen 2 Prius Care, ... Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by NorthStar, Jul 26, 2005. ... I am getting the red BRAKE LIGHT, the amber waming symbol, ABS, and ... VSC, ABS, (!) and emergency brake light on
Feb 5, 2010
Brake, Brake warning, ABS, VSC appear
Oct 5, 2008
More results from priuschat.com

you will need to hook up a scan tool, I know many parts stores will loan you one or let you use it in the parking lot, VSC could have something to do with a wheel mounted speed sensor, did you hit something? any noises, try this and see if it goes away

1. • 1 Shut off the vehicle's engine and apply the parking brake to protect yourself while working on the vehicle.
     
   • 2 Open the vehicle's hood and examine the engine compartment. Locate the air filter box mounted to the left of the engine. The air filter box features a black exterior, square in shape, and a large ribbed intake hose.
     
   • 3 Check all of the small black vacuum lines surrounding the air filter box. Reconnect any disconnected or loose vacuum lines you find.
     
   • 4 Start the engine and drive the vehicle to clear the "VSC" warning light displayed on the dashboard. If the VSC light fails to go out after driving the vehicle normally, proceed to the next step.
     
   • 5 Park the vehicle, turn off the engine and set the parking brake. Open the vehicle's hood and disconnect the battery's negative cable for 15 seconds, using an appropriate size socket. Disconnecting the negative battery cable will reset the vehicle's computer and clear the "VSC" warning.
     

Look in your owners manual

Can also find those symbols on the internet

NEED CODE FAULTS AND THE ECUS THAT THEY COME ON!!

Hello and welcome to FixYa... the Engine light and VSC light will come on together when a fault code is stored in the computer
...the codes will need to be read to determine what caused it, based on that information, repairs needed can be taken to correct it...i hope this helps and good luck with the Lexus

This just happened to my 08. What was wrong with yours?

For some reason on Toyota and some Lexus vehicles certain check engine light CEL issues also result in the ECU lighting up the vsc trac and vsc off lights. The ECU actually switches these anti skid and anti lock brake systems off and the lights are to remind you that they are disabled. 1) Check that the fuel cap is on securely 2) Check the oxygen sensors on the exhaust, check that connections are clean and there are no missing wires. 3) Have someone check the on-board diagnostic codes if the CEL is still on

Battery was diconnected for 1 minute and then reconnected. All lights are off.

It stands for Vehicle Stability Control When the VSC system takes control it activiates stability correction. The slip indication light flashes while the buzzer activates. The VSC is able to operate at all times except when the centre differential is locked. When the centre differential locks, the VSC-OFF light in the combination meter illuminates to inform the driver that the VSC function has been turned OFF. The centre differential lock is designed for freeing the vehicle if it is stuck in mud for example, however it would be difficult for the vehicle to free itself if the engine output were reduced due to the operation of VSC. Therefore when the centre differential is locked, the VSC function is turned OFF.If a malfunction occurs in the VSC system, the VSC warning light illuminates to alert the driver. If the vehicle with VSC begins to oversteer or understeer because of an emergency avoidance measure, or by excessive speed in a corner, VSC will automatically activate. By adjusting the engine’s power output and braking each wheel independently, VSC helps to return the vehicle to a ‘zone of stable operation’..