Replaced battery still get message in dic
SOURCE: All wheel drive disabled message on DIC in 2005 Buick Terraza
if its just a button then reingauge it. That should do it.
SOURCE: programing instructions for buick 2006 lacrossekeyless remote fob
Transmitter ProgrammingImportant:
All transmitters which are to be recognized by the remote control door
lock receiver (RCDLR) must be programmed in a single programming
sequence. If the system is placed in program mode it will erase all
previously programmed transmitters upon the receipt of the programming
signal from the first transmitter. Up to 4 transmitters can be
programmed. Do not operate or program the transmitters in the vicinity
of other vehicles that are in the keyless entry program mode. This
prevents the programming of the transmitters to the incorrect vehicle.
Good luck
SOURCE: 2006 buick lacrosse how to replace headlight low
The bright light fitting is the same as the dim so take it apart fist to see how the cover screws off/on and the light comes out. Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise. Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light. On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again. Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw. Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough. If not, then you need to release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit. To remove these locking pins, pull or pry up the little tab in the center of the pin just like you were pulling a nail by the head. That should give you a little more space.
SOURCE: Replace headight assembly on 2005 buick lacrosse
The procedure to replace head light assembly on buick lacrosse is as follows:---
1)To remove and replace the headlight assembly you will need to remove 1 retaining bolt on the top of the headlamp assembly and 2 sliding retainers at the rear.
2) The carefully Pull up the retainers and that will release the headlight assembly and allow you to pull it out the front.
3) When installing the new headlight assembly make sure you have it lined up correctly before trying to install the retainers, don't force them it may get cracked .
4) Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise.
5) Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light.
6) On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again.
7) Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw.
8) Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough.
Note:-- The turn signal is part of the headlight assembly on your 2005 Buick LaCross.
9) To replace the headlight bulb you need to remove the front bumper cover.
10)To release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit.
11)To remove these locking pins, pull or pry up the little tab in the center of the pin.
Thanks.
SOURCE: replace thermostat on 2005 buick lacrosse
hello there:
to replace the thermostat you will need to fallow the upper radiator hose back to the intake you should find two bolts holding the thermostat housing remove the bolts and you should find the thermostat under the housing you will need to remove the hose this will help you out and before in stalling clean gasket surface on both sides..... please leave a review thanks sincerely D.Jones
208 views
Usually answered in minutes!
×