What are the torque specifications for a 2003 Nissan Maxima 3.5 liter
Here's a link to your torque specs.
SOURCE: Torque and sequence to Intake Manifold for 3.3L Nissan Xterra 2000
Hi El Faraon,
I believe that you're dealing with 12 mm bolts and nuts....THESE ARE NOT THE SPECS FOR YOUR ENGINE, but I believe that if you use them you'll be close....Tighten in three stages up to 22nm....choose the bolts from the centre of the manifold and circle outwards until you reach the last one.....It may be a good idea to draw an overhead or plan view of the unit, marking out the bolt positions.....Start at the centre and mark the sequence and follow that....What is important is starting at the centre, so that nothing becomes warped....
Hope this helps,
Regards, Johngee10
SOURCE: torque converter mulfunction
This is a circuit code. It could be the Transmission control module(TCM), the solenoid, or the wires in between. I would start by checking the wires running between the transmission control module and the transmission. Look for any obvious signs of chaffing or breakage. If the harness is ok, replace the solenoid pack in the transmission. If this still doesn't fix, replace the TCM.
SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002
frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!
SOURCE: Bolt torque specs for flywheel, pressure plate,
1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.
Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.
Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!
Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)
If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.
SOURCE: torque settings for cylinder head nissan sentra
Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees
1,369 views
Usually answered in minutes!
×