2001 caravan trailer wiring

There is a tail lights fuse for the truck, but not for the trailer.
First, check that your left tail light on the truck is working, if not fix the problem (new bulb, bad contact, fuse).
Then the obvious suggestions regarding the trailer are: Check the tail light portion of the bulb to be sure it is not blown. If good (best to put in new one to be sure), then check the wiring from the front of the trailer all of the way to the non working bulb, including every connection and at any place it is secured to the trailer frame. If all is good with the trailer circuit and bulb, then check the truck's trailer connector, including any adapters. If by chance the truck is wired with a flat 4 wire harness the problem may be solved (but usually the blinkers are the problem). Modern trucks require a 5 wire harness which self adapts to the standard 4 wire trailer circuit. Check for dc power (12 volts) from the truck's female connector. One wire will be ground, others will be taillights (turn on headlights), brake lights (have someone press brake pedal), and blinkers (turn on switch and blinkers).

We do not have the wiring diagrams. But here is the red neck method, use a 12 volt test light probe tool (any parts stores for $5) and as a friend operates each light circuit, probe the connector or harness and see what lights up, then mark the wire color and what it does, brake lights, turn signals etc.

Your vehicle CANNOT be wired for a trailer without using the converter box. The only vehicles that do not require a converter box are the vehicles that use the stop lamp bulb as a turn signal. Your vehicle is equipped with SEPARATE stop lamp and turn signal bulbs.

To make the converter box work correctly, it must be wired according to the instructions to BOTH the stop lamps AND the turn lamps. The tail (or PARK) lamps DO NOT go through the converter box.
Your trailer uses the SAME bulb for stop and turn - THIS is the reason you need a converter.

The wire color for both your LEFT TURN and your RIGHT TURN are LIGHT GREEN/TAN. Although the wire colors are the same at the bulb sockets, these are SEPARATE circuits and must be wired to the correct wire at the converter box. (LEFT and RIGHT) The converter box will have an INPUT connection for EACH of these.

The wire color for your STOP lamps is WHITE/TAN. The converter box should only have one INPUT wire that connects to this. It doesn't matter which side of the vehicle you connect this wire to. All of the stop lamps are on the same circuit.

The converter will then have only one wire for LEFT turn and stop (usually YELLOW) this is the wire that needs to go to your trailer connector for left turn and stop.
The RIGHT turn and stop will most likely be GREEN coming out of the converter.

You need to install a 3-2 wire converter. I suggest a CURT 56175 then
1.Using a test lamp, identify the corresponding wires in the harness for the left turn, right turn, tail lights and brake lights. 3. Temporarily remove the vehicle's negative battery cable from the battery. 4. Using wire taps, attach the input wires of the tail light converter to the corresponding vehicle harness wires identified in step 2 as indicated.
Converter Brown Wire: Tail Light Circuit Converter Yellow Wire: Left Turn Circuit Converter Red Wire: Brake Light Circuit Converter Green Wire: Right Turn Circuit
5. Locate a suitable mounting location for the ground eyelet on the vehicle near the converter on vehicle's frame or cross member.
And your ready to tow!

With both tail light lenses removed locate the black with yellow wires and the dark green with brown wires coming out of the brake/tail/turn signal sockets.

The black with yellow wire will be the running lights or tail lights and the brown wire from the trailer harness will attach to it.

The green wire on the trailer harness will be the right turn signal and will be attached to the passenger side tail light harness dark green with brown wire.

The yellow wire on the trailer harness will be the left turn signal and will be attached to the dark green with brown wire on the drivers side tail light harness.

The white wire on the trailer harness is the ground wire and will need to be attached to a good ground. Is it pretty easy to crimp an eyelet onto the end of the wire and use a self tapping screw to attach it to the body behind one of the tail light lenses.

Here is a trailer light/wiring article I have done in the past. It has a couple of good tips you may find useful.

http://www.hotspotoutdoors.com/forum/ubbthreads.php/topics/1425999/1/Trailer_Wiring_101

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Tail lights and brake lights are on the same wire.
Connect the wire from the brake light to the connector in the car to the tail lamp wire connector and you will be set to roll

One wire is for the brake/directional filament and the other wire is for the tail light. The fixture should be grounded when it is attached to the bracket. To test which is which (the brown wire is USUALLY the ail light) make sure the fixture is grounded and touch a hot wire to each of the wires coming from the fixture. Watch to see which wire lights up the brighter filament and this is the brake/directional light. The dimmer filament if the tail light. Brakes lights and directional lights are both the same filament. Wen the brakes are applied, both lights are activated. When a direction light is turned on, it simply flashes the brake light filament.

Hey Boon,

The pinouts for a 7-way plug are as follows:
Seven wire Trailer plugs:

Horse, stock or utility trailers:
White = Ground - 1
Blue = Electric Brakes - 2
Brown = Tail and clearance lights - 3
Black = Battery, aux power - 4
Yellow = Left turn/Brake - 5
Green = Right turn Brake - 6
Orange or Purple (not both) = Auxilliary or Reverse - 7

Recreational Vehicle:
White = Ground - 1
Blue = Electric Brakes - 2
Green = Tail and clearance lights - 3
Black = Battery, aux power - 4
Red = Left turn/Brake - 5
Brown = Right turn Brake - 6
Yellow = Auxilliary or Reverse - 7

In both cases 4 is battery and 7 is reverse, aux or not used.

Double check your wiring using these lists as a reference.

Click here for my post on Trailer wiring

This should get us closer to the answer.

Best regards,
Mike

brown to the tail lights. yellow to left turn signal. green to right turn signal. this is a basic 3 wire hook-up i use all the time w/4wire connectors for all trailers. white wire is not used. ground is established when you hook to the ball.
to find the correct wire to splice to, use a testor (has a clip to the bare wire, and a sharp point to the truck frame). using a needle, push it through a wire to rear light harness. turn on the turn signal. check if the connection is the blinker, testing until you have the blinker wire. the tail lights can be attached to the license plate wire. brakes and blinkers use same wire, so brake lights will work whenever the turn signal is attached.
to be sure everything is working right, have a second person go inside the truck and work the signals, brakes and lights one at a time while you are at the back of the trailer telling what to do.

the issue is the trailer, negative or power feed back,check grounds